RC10Talk - The Net's Largest Vintage R/C Community

In short, a very good weekend as usual, with a great atmosphere and top-notch organization (we won't mention the 4x2 GAS TT race scheduled for 11:00 a.m. (eleven: zéro zéro ;) ). But why, oh why not talking about the TT GP race start procedure 🤣😂😂??? 11:00 - Call for the participants, 3 buggys are ...

I think I'll just leave everything packed up from Montlucon, throw it back in the car in June and head straight for Beleysanne!!!! My regret from this past weekend was not spending more time looking at all the cars you brought Trass.....the collection is amazing and I'll be sure to pass your table ...

The H2D arrived on tuesday... It is currently installed in the living room, as the final destination is not ready yet. https://i.imgur.com/vYVeZla.jpeg I did not print much yet with it... https://i.imgur.com/Yse6Bji.jpeg https://i.imgur.com/7WMYGNV.jpeg https://i.imgur.com/cnamw7J.jpeg Someheow it w...

After the first face of the support yesterday, I came back to the fablab this morning to work out the second face, and the chamfer... https://i.imgur.com/BuAZQUj.jpeg It was done with pockets first (and to optimise machine tool time, I could have done contours rather than pockets, something I notice...

On the sunday, there was less people, and most of the guys of the club wanted to try the pancar. This gave me the opportunity to gather reliability data with a quite intensive stress test... B6cmCqODlfg The car ran for about one hour and a half with a few pilot. One of the guys changed the diff sett...

For me, the whole purpose of the H2D is dual material and prints without waste and cross polution between materials. I did a first attempt today, by mixing TPU and PLA in a print: I have a whole set of use case I thought about relying on this, and I want to put that to test... I sliced a Marui Shogu...

I ran the Zerda 2GT on the Track in Montluçon during the event, and @TravelinTravis was there to take a short video -Thanks Travis!

The print quality of the X1C was great... The H2D sets the quality to another level... This is an ABS print, and I never had such great quality with the X1C or the A1 mini... https://i.imgur.com/nii1xxk.jpeg This is an exhaust port I found on makerworld (I could have done the same, but was already d...

The exhaust port was installed, and I connected a pipe to an Xtool AP2 air purifier. I got the laser combo as my wife has some light requirements for a laser. Laser module installation is very straigth forward : you just have to put the module in place, plug it, plug the air assist tube on the modul...

I procrastinated a lot recently... The publication for the 312 bodyshell accessories is still awaiting I do the instruction manual, and I had to finish the 917K accessories... I defined the cut line for both arches and the side line. A printed part will do the job... https://i.imgur.com/8ykSM7z.jpeg...

During Montluçonnaise, my friend Benoit put a box with some goodies in my truck. I was aware of the NIB, but did noticed the assembled one only later, and I only check the content once home. https://i.imgur.com/ubHWuuv.jpeg https://i.imgur.com/K78FUhR.jpeg So in short there is a Tag Jet 1/10 NIB and...

Just published an alternative battery fixation allowing for quick release...
https://makerworld.com/en/models/1466375-battery-quick-release-for-st-1-ef-209-rc-pancar

The principle is simple, it replace the bridge I implemented initially with 2 parts and a reusable cables tie with scratch...

Finalizing the files takes time. I first added all hardware in Fusion360, then made the joints, then organized and then took snapshots... https://i.imgur.com/tnD3vvf.png https://i.imgur.com/xk7uhsB.png And all this to make a simple instruction manual... A few hours of work! The 917K should be quicke...

It's a bit too hot right now to do something else, so I finalized the 917K and published it. Again same process than for the others was applied... https://i.imgur.com/yEwKH89.png https://i.imgur.com/uK5boO1.png The accessories for the Delta Plastik Porsche 917K (available at Mantua Models) are now p...

The Zerda ran at Montluçon few weeks ago. But it was with the main belt longer than what was required, with adjustment of the tightener rollers diameter to make it fit. The proper belt arrived the day before Montluçon, and I had no chance to change it before the event or during the event. I decided ...