RC10Talk - The Net's Largest Vintage R/C Community

They snuck in a nice little HIP sticker too, LOL.

I just resurrected my Team Associated RC-10 2T Championship buggy from a long slumber and found this forum. Purchased new in 1991 and using an MSC and Futaba controller and electronics. Old NiCD battery holds a charge for about 3 or 4 minutes. So off to get a 3800Mah NiHM Tenergy and charger from Am...

In 1983 Tamiya would strike lightning twice with its popular 1/10 2wd electric off-road racing buggy, the Frog. Sharing the ORV (Off Road Vehicle) chassis with the well-known Subaru Brat and lesser-known Lancia Rally car meant the Frog's guts were supported by the ORV's molded plastic space frame st...

2025 Vintage Off-Road Nationals

September 5th-7th

Adrenaline R/C Racing
246 Sulky Drive
Winchester, VA 22602

Classes and Rules - http://vintageoffroadnationals.com/rules/

** The website is down at the moment so I can't link the classes/rules at this time **

If anyone has this car I stupidly sold 8 years ago, give it back please

Hi folks, Did a 3d printed design for battery holder for Kyosho Optima/Javelin. This is designed for low profile shorty pack that followed the dimension of 18.5x47x96mm. The original intent to have a better battery secure rather than velcro tapes and prevent the battery from moving sideway. IMG20250...

If it keeps raining, gonna make its 1st pass tommorrow, running a little more rocket that I want to start with, the lower power engines never got delivered...ordereded April 19th

IMG_2516.png ** CASH ONLY ** All classes are 2s lipo or 6 cell NiMH (no voltage check) All classes are Blinky Open tire ( Jconcepts Green Double Dees and Sprinters are a popular choice) Classes: 2wd buggy - 17.5. 1997 cutoff (ex. - B3, XX and older) Stadium Truck - 17.5. 1997 cutoff (ex. - T3, XX-T...

In 1984 Tamiya released alongside the Grasshopper a higher performance 1/10 2wd electric off-road buggy named the Hornet. As a stablemate to the Grasshopper the Hornet shared the same deeply molded ABS plastic monocoque chassis with integrated shock towers and long front swing arms suspended by slid...

Weather here sux, got it all ready, but over my better judgement the 💎 One talked me into not running that E engine and wait for the smaller engines...but did put a 20t pinion on it and baselined it with no rocket...it's got a Tamiya BZ motor in it..surprisingly it ran 33mph...alot faster than I was...

Front wheels: This was a pain and I bought a number of parts that ended up not working. The plan was to use Ultima 4mm axles and the GPM Tamiya adapters along with new 4x8 bearings. The problem is the factory Ultima axles are way to short. I am sure at some point longer aftermarket axles were availa...

oh just saw the poll, wow people really have bad taste in wheel color :lol: Come on guys, the original 1:1 wheels were Magnesium why would you want to paint over that with boring black paint? Because in this instance the silver is too busy, the black wheel looks more aggressive by allowing your eye...

Totally, same car over and over who thinks he is going to win if the marshal just gets to him 3 seconds quicker on his 37th crash, been there! Generally though I have found most people to have the right attitude. Always a couple though and in my experience those couple are not always the slow guys.

THEYTOOKMYTHUMB wrote: ↑Sun May 04, 2025 2:01 pm The Magnesium does look good. It's just when I picture the car after the unveiling, I think the black will look best. But I'm also the guy that RIT dyed every single RC car part black bitd.

Can't believe u like the black

THEYTOOKMYTHUMB wrote: ↑Sun May 04, 2025 2:01 pm The Magnesium does look good. It's just when I picture the car after the unveiling, I think the black will look best. But I'm also the guy that RIT dyed every single RC car part black bitd.

Black sux, plain and simple Benji. If u like it better u need to go to the doctor.