guess i should give an update, I ended up just running it (motor housing) in an ultra sonic cleaner with a few cleaners, dish soap & some floor cleaner. I let it run for an hour or so. Dried it out with a micro fiber cloth so it didnt leave lint or anything inside it. Afterwards I push hot air with a blow dryer through the motor to finish trying it out. Seems like there was still a little corrosion visible but it did clean out some of it. Put it back together and ran the car about 30 mins later
That in combination with a tranny rebuild with new differential & bearing throughout the car and its run good as new.
Just figured I'd share a couple pics of my #9000 B2 racer rebuild project. Nothing too crazy, just trying to fix her up a bit. I've had the car for a year or so, it was a mess, the previous owner had all kinds of weight glued into the front and rear...
Last post
I blame Tower for the wrong pictures compared to what is actually received. Most people just steal Towers photos for their listings. Many a time I've ordered AE things only to have them arrive looking completely different. Mufflers, headers, exhaust...
I did a search on this and nothing good popped up so if this has been covered in the past I apologize.... I am looking to rebuild the shocks on my RC10. Is there any type of a kit out there to help with this, or directions? I don't want to screw...
Last post
Depends on the shocks condition, they may just need a clean - but then it is best as said above to at least replace the o-rings, you can get away with polishing the shock shafts as long as they are not bent. If they are the hard anodized shocks...
Hello all. I am new to this forum but not new to the AE world. I have been involved with this hobby for about 20 years. My first Hobby grade RC was a Kyosho Big Brute, I got when I was 8 years old. About two kits later I recieved an RC10T for my...
Last post
nice looking truck, I think your daughter will enjoy it a lot. Nice to see that I'm not the only one dying my parts :D I am glad someone took the plunge and installed the new trans on an old chassis. I thought of doing this myself, but decided not...
I am now determined to rebuild his thing and make it spin at least 16 seconds! I already took it apart and started working on it. I'm ordering ABEC 7 ceramic bearings for it. What I have now are ABEC 1s. ABEC meaning how well the bearings turn. When...
Last post
Do the outdrive slots have any raised burrs on them from dogbone wear? That can make the bearings hard to press over the outdrive.
The outdrives got a quick freshening with a small file for any burrs, and a super quick polishing for surface rust....
I Have Had A RC10 Graphite Since 1990 Or 1991.Everything works In It Runs Great. Just Checking To See If I Can Upgrade The Motor To A bushless And Witch One Would Fit. And I Like To Up Grade The Electronics In It What Would Be Good Upgrades That...
Last post
Junk? :shock: No RC10 is a junk car. :) It sounds like it may be a Team Car which is a cool car. If it has a milled out interior chassis and yellow wheels it would be a Worlds Car which is really cool.
Hello.
As said in my presentation I put some photos of my RC10 CE which spent 20 years in its box in the garage.
It is a model with the 6-gear gearbox, bearings everywhere, a ROBBE ECO 2-WAY 27Mhz AM radio, standard 27-turn YOKOMO motor, and a...
Last post
Just realized you built your own ESC, nice work! That's awesome. Man the French RC mags were way ahead of RC Car Action I guess... 😆
Hello! I recently started working on an old Gold Pan. It has a futaba reciever, a futaba 63003 servo, VXL-3s ESC, a Velineon 3500 motor, and a stock 6 speed trans. It was working great for a while. really fast. Here recently though, it wont work....
Last post
My mistake, it went 58. I'm not sure the battery. It was a lipo I borrowed from a friend. I was running 31 on the pinion. Not too sure on the spur.