Steering

Moderators: scr8p, klavy69

1 post • Page 1 of 1

woodall01: Approved Member; Posts: 46; Joined: Thu Apr 24, 2014 4:15 pm; Location: Orlando Florida USA

Steering

Quote

Post by woodall01 » Sun Aug 24, 2014 3:41 pm

Stupid question, has anyone had luck at tightening up the steering on the Worlds I have replaced the bell cranks with JConcepts and replaced the servo horn with a metal horn. I have a metal geared servo (Savox). It turns great, it just seems like it has way too much play.

Post Reply

1 post • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

B3 steering end point issue - not enough steering lock

Last post by RC10th « Fri Apr 29, 2016 10:24 am
Posted in Temple's RC10 Tech Forum
Replies: 1
by green510 » Fri Apr 29, 2016 8:37 am » in Temple's RC10 Tech Forum

First post

Hi all,
Just buttoning up the finer details of my project and am stuck with this one.

RC10 B3,
recently re-assembled as per manual.
Savox SC1251-MG servo
Spektrum dx4c set to 150% steering capacity.

It only has 3/4 steering capacity with a touch...

Last post

If you disconnect the linkage at the servo can you turn the wheels fully by hand?

Not familiar with the 4c but is it possible the dual rate is turned down even though EPA is turned up?

1 Replies

1088 Views

Last post by RC10th
Fri Apr 29, 2016 10:24 am
need more steering.

Last post by yellowdatsun « Fri Oct 30, 2015 8:57 pm
Posted in Temple's RC10 Tech Forum
Replies: 9
by twisted » Wed Oct 28, 2015 11:12 pm » in Temple's RC10 Tech Forum

First post

race day is coming up and after some practice i noticed the car has a heavy push in the high speed sweepers. its also pushing mildly on tight corners. from my initial set up that you can see here :

i went up to 40wt oil and a heavier spring in...

Last post

slightly stiffer front spring

That alone was the biggest mistake. Stiffening the front end will create more push

9 Replies

1178 Views

Last post by yellowdatsun
Fri Oct 30, 2015 8:57 pm
steering

Last post by juicedcoupe « Wed Jun 22, 2022 2:06 pm
Posted in Modern Electronics
Replies: 2
by seitzxvx » Wed Jun 22, 2022 11:03 am » in Modern Electronics

First post

Trying to decide on a mini servo for steering and not break the bank.
Any help would be appreciated.

Last post

There are different sizes of mini servos as well, some bigger than others.

2 Replies

418 Views

Last post by juicedcoupe
Wed Jun 22, 2022 2:06 pm
Steering id

Last post by mikea96 « Thu Sep 29, 2016 11:04 pm
Posted in RC10 Buggy Forum
Replies: 2
by mikea96 » Mon Sep 26, 2016 5:03 pm » in RC10 Buggy Forum

First post

Who is the manufacture of these steering bell cranks?

Last post

Yeah i think they are homemade

2 Replies

694 Views

Last post by mikea96
Thu Sep 29, 2016 11:04 pm
T2 steering

Last post by Bugle « Mon Mar 16, 2009 3:19 am
Posted in RC10 Truck Forum
Replies: 8
by vintagerc10 » Wed Mar 04, 2009 3:16 pm » in RC10 Truck Forum

First post

I've been working on converting my old rc10 in into a rc10t. I still have the old bugger steering set up and have been looking to upgrade. I'm a novice and read some about the ball bearing bellcranks (?)

would the steering set up out of RC10 T2 be...

Last post

That's only a problem with the composite craft setup though, the standard bellcrank has servo arm mounting holes further out.

8 Replies

1554 Views

Last post by Bugle
Mon Mar 16, 2009 3:19 am
Steering Assembly ?

Last post by slvrback « Fri Jun 07, 2013 7:22 pm
Posted in RC10 Truck Forum
Replies: 3
by slvrback » Fri Jun 07, 2013 6:07 pm » in RC10 Truck Forum

First post

Found these in my box, not sure if they will work on my original RC10Ts. Are the steering arms too short? Also the one in the upper left for a T4?

Last post

Yup, file is to big. I'm Using my Ipad . Ill try my cell phone

3 Replies

647 Views

Last post by slvrback
Fri Jun 07, 2013 7:22 pm
RE-RE bellcrank steering ?'s

Last post by scr8p « Mon Jan 20, 2014 5:29 pm
Posted in RC10 Buggy Re-Release Forum
Replies: 5
by kaiser » Mon Jan 20, 2014 3:39 pm » in RC10 Buggy Re-Release Forum

First post

i bought asc 6252 rc10 bellcrank steering

with those short screws and no nuts, how is this supposed to stay in the car?

i ended up installing a houge from another car in my ce, but these would have looked very nice in there.

i suppose i could...

Last post

if using them on a graphite chassis, use the longer 7/8 8-32 screws, install the shanked on the chassis (like you would a houge or a&l bell crank with the nut down), slide on bell cranks and secure with some 8-32 nuts.

5 Replies

1285 Views

Last post by scr8p
Mon Jan 20, 2014 5:29 pm
rc10 steering

Last post by MONSTER « Thu Feb 05, 2009 12:19 pm
Posted in Temple's RC10 Tech Forum
Replies: 5
by longboardnj » Wed Feb 04, 2009 11:40 pm » in Temple's RC10 Tech Forum

First post

does anyone make stock or like stock 6 gear rc10 steering (like pic) or worlds car steering part no. 6254 ?? i want to use Associated Aluminum Flat Head Screws 8-32x7/8 not rc10t/rc10gt special steering screws. any help,pics,links would be great

Last post

I got Set of those in my recent Treasure Box(s). MAN, they are BUTTERY smoooth after I cleaned/lubed em up. Theyre AWESOME!!!

5 Replies

1098 Views

Last post by MONSTER
Thu Feb 05, 2009 12:19 pm

Return to “RC10 Buggy Re-Release Forum”

Who is online

Users browsing this forum: No registered users and 5 guests

Steering

Steering

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online

Login Register