Help identifying type of dual slipper

Moderators: scr8p, klavy69

6 posts • Page 1 of 1

isles1: Approved Member; Posts: 86; Joined: Sat Jan 24, 2015 12:42 pm; Location: New York, USA

Help identifying type of dual slipper

Quote

Post by isles1 » Thu Nov 12, 2015 1:22 pm

I pulled this dual slipper setup off of an XXT. Any idea who manufactured the light weight slipper plates and spur? Spur is noticeably thicker than the Losi dual slipper spurs. Thanks.

Losi XXT build (sold): http://www.rc10talk.com/viewtopic.php?f=27&t=39172

Losi XX-CR BK build: http://www.rc10talk.com/viewtopic.php?f=27&t=37851

Losi XXT-CR build (sold) http://www.rc10talk.com/viewtopic.php?f=27&t=38786

LosiXXkid: Approved Member; Posts: 757; Joined: Sun Mar 03, 2013 5:35 pm; Location: Islington, North London; Has thanked: 2 times; Been thanked: 6 times

Re: Help identifying type of dual slipper

Quote

Post by LosiXXkid » Thu Nov 12, 2015 2:06 pm

The spur looks like one made by Kimbrough and the slipper plates look like they could be standard Losi ones with additional holes drilled to lighten them.

~I'm a lot older now than I was then and wish that I knew then what I know now~

isles1: Approved Member; Posts: 86; Joined: Sat Jan 24, 2015 12:42 pm; Location: New York, USA

Re: Help identifying type of dual slipper

Quote

Post by isles1 » Thu Nov 12, 2015 2:34 pm

Possible, but the hole spacing seems too perfect to have been done after the fact.

LosiXXkid: Approved Member; Posts: 757; Joined: Sun Mar 03, 2013 5:35 pm; Location: Islington, North London; Has thanked: 2 times; Been thanked: 6 times

Re: Help identifying type of dual slipper

Quote

Post by LosiXXkid » Thu Nov 12, 2015 3:12 pm

isles1 wrote:Possible, but the hole spacing seems too perfect to have been done after the fact.

Do the plates have anodizing on the inside of the holes?

~I'm a lot older now than I was then and wish that I knew then what I know now~

isles1: Approved Member; Posts: 86; Joined: Sat Jan 24, 2015 12:42 pm; Location: New York, USA

Re: Help identifying type of dual slipper

Quote

Post by isles1 » Thu Nov 12, 2015 3:27 pm

Yes

LosiXXkid: Approved Member; Posts: 757; Joined: Sun Mar 03, 2013 5:35 pm; Location: Islington, North London; Has thanked: 2 times; Been thanked: 6 times

Re: Help identifying type of dual slipper

Quote

Post by LosiXXkid » Thu Nov 12, 2015 3:28 pm

isles1 wrote:Yes

Hmmm! Definitely not home made then......

~I'm a lot older now than I was then and wish that I knew then what I know now~

Post Reply

6 posts • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Help identifying vintage dual resistor MSC...

Last post by b027 « Tue Sep 28, 2021 8:14 pm
Posted in Vintage Electronics
Replies: 3
by b027 » Mon Sep 27, 2021 9:11 pm » in Vintage Electronics

First post

Hey there!

I've been lurking for a while, and have recently gotten back into my RC10's. Now I need some help - I picked up a box of vintage parts locally with RC10, Tamiya, and Kyosho parts, among others, and it included what appears to be a...

Last post

Thanks both! This is great information, especially the wiring diagram and instructions! Amazing

Any idea what the “8/10” might refer to?

Do you know where these were typically used? I don’t think I’d run it, but would consider a shelf build if I...

3 Replies

408 Views

Last post by b027
Tue Sep 28, 2021 8:14 pm
how to get from hydra-drive to dual slipper using modern...

Last post by Mr. ED « Sun Jun 14, 2015 10:28 pm
Posted in Losi Forum
Replies: 9
by Mr. ED » Sat Jun 06, 2015 11:08 pm » in Losi Forum

First post

I'm thinking of maybe putting some effort in getting an old xx back into running shape.
It has a hydra-drive in it already, but not in a very good condition, and I don't have spare spurs to use with it.

I think I've read about it being possible to...

Last post

Picked up a very ugly looking XXT yesterday; rusted, bent turnbuckles, 3 missing springcups, no body, nor front body mount and a broken front bulkhead, and lots of grime and dirt.
It does however have fully intact replacement parts for all the ones...

9 Replies

2031 Views

Last post by Mr. ED
Sun Jun 14, 2015 10:28 pm
Vintage trans, LRM Slipper vs Lethal Weapon Slipper vs MIP Slipper vs XX retrofit slipper

Last post by GoMachV « Mon Jul 09, 2018 11:18 am
Posted in Losi Forum
Replies: 4
by Snappy1 » Sun Jul 08, 2018 9:21 pm » in Losi Forum

First post

I am building a New parts Losi JRX2 , it's very near complete, but after reading through much of this section I am in two minds regarding the trans choice.

Currently it has a new built LRM slipper with a A-3020 bearing diff, what trans would be the...

Last post

Are the spur gears for the lethal weapon easily available ?

Yes, they use standard old school pan car style gears like Kimbrough.

4 Replies

1347 Views

Last post by GoMachV
Mon Jul 09, 2018 11:18 am
Stealth slipper conversion to B4 slipper - have questions

Last post by mdutcher « Fri Nov 08, 2013 6:29 pm
Posted in Temple's RC10 Tech Forum
Replies: 4
by mdutcher » Fri Nov 08, 2013 4:43 pm » in Temple's RC10 Tech Forum

First post

Ok, I have searched and searched and could not find any specific details regarding converting a stealth slipper to accept a B4 slipper. Please point me to a thread that details this out if you could.

I have the parts to do it. I thought that it...

Last post

Got it now. Thanks for the info.

I have the wrong one.

4 Replies

1268 Views

Last post by mdutcher
Fri Nov 08, 2013 6:29 pm
ASC9253 (B3/T4) Slipper Disk in a Stealth Slipper????

Last post by CBR240 « Fri Mar 29, 2013 5:34 pm
Posted in Temple's RC10 Tech Forum
Replies: 14
by CBR240 » Thu Mar 28, 2013 6:11 pm » in Temple's RC10 Tech Forum

First post

Hope this isn't a stupid question, but it probably is. :) Feel like I am missing the obvious here.

After 23 years of RC10 ownership, I just bought my first stealth trans a few months ago. Really, I'm kind of late to the game here. I like the...

Last post

No worries, in the picture it really does look like they are mounted on the back of a white tower, when they are actually on the front of a black tower. I had a What!!!??? instant myself when I looked back at that picture. :D

14 Replies

2757 Views

Last post by CBR240
Fri Mar 29, 2013 5:34 pm
AVID RC Triad Slipper Clutch vs AE VTS Slipper Clutch

Last post by Dirtcar75 « Wed Nov 28, 2012 1:30 am
Posted in RC10 Buggy Forum
Replies: 15
by RC104ever » Sun Oct 07, 2012 1:05 pm » in RC10 Buggy Forum
1

2
First post

Hey guys, just wondering if anyone here has tried either setup on the RC10? Since many of us have upgraded the top shaft to a B4 one, I would think that we could use either setup but I wanted to see if anyone here had any experience with either...

Last post

No i made it.... There are a bunch of pics in a thread i started in the vintage truck section
15 Replies

3998 Views

Last post by Dirtcar75
Wed Nov 28, 2012 1:30 am
Getting my Ultima RB Type-R going

Last post by Brandon G « Sat Jan 21, 2012 8:24 am
Posted in Kyosho Forum
Replies: 2
by KyoshoScorpionKid » Fri Jan 20, 2012 12:22 am » in Kyosho Forum

First post

I have this Ultima RB Type-R chassis ready to go just wondering if anyone has one. I have 2 one New in the Box and this one I purchased from ebay a long time ago love driving 2wd drive cars.

IMG_0301.JPG

Thanks
Franco

Last post

Here's mine:

Nice buggy, looks a lot like a B3 though. :D

2 Replies

803 Views

Last post by Brandon G
Sat Jan 21, 2012 8:24 am
Ultima RB Type R

Last post by HiTec « Fri Jan 29, 2021 7:00 am
Posted in 21st Century Modern
Replies: 24
by Momo5 » Fri Sep 30, 2011 1:09 pm » in 21st Century Modern
1

2
First post

Does anyone have one of these? If so post some pics. It looks almost like a B3.

Last post

Sorry to bump and old thread, but i just now saw the comment about the chassis being too long. I have a fix for it if someone still has these cars. I have released an 3D printable chassis with two versions. First one is stock length and second is...
24 Replies

4384 Views

Last post by HiTec
Fri Jan 29, 2021 7:00 am

Return to “Losi Forum”

Who is online

Users browsing this forum: No registered users and 12 guests