I haven't received a reply from HPI regarding the offset but I've confirmed through other sources that they do fit 12mm hex. Here's the list of vehicles they will fit from the HPI site:
THIS PART FITS THE FOLLOWING KITS / PARTS:
E-Firestorm 10T
Firestorm 10T 3.0
Wheely King 4x4
E-Firestorm 10T Flux
I'll check the offset once they've arrive and are fitted to the truck. If the offset isn't exactly perfect, I feel pretty confident that I can make adjustments via alternate hex drive thickness or maybe trim the back of the wheel if necessary. Based upon the photos I've seen, they appear to fit. I'll post an update later.
It is would be very difficult to fit those mountaineer wheels to your TF2. You would be better off finding a 12mm hex mount wheel that looks like these. Here is a set on eBay
Oh, those are really nice. I have a similar set on my Jeep JK converted SCX10 except the bead lock rings are annodized gun metal.
Anyway, for the TF2, I went ahead and ordered a full set of 2.2" HPI 3062 wheels with 12mm hex drive and should fit the truck just fine (I hope). They look similar to the Tamiya Bruiser wheels but don't require that funky 3-screw hub to mount them.
The wheel does use a 12mm hex, unfortunately I would need to measure one of the wheels to find the measurements you require.
At the moment they are out of stock and not due back for another few weeks. I would suggest looking online for a store that has them in stock and they will be able to provide this measurement.
Kind Regards
Josh Nixon
HPI
Customer Service Technician
therigliveson wrote: ↑Mon Oct 29, 2018 9:47 pm
If you aren't fixated on 1.9 wheels, I used some 2.2 RPM revolvers in the past...very similar look and stretched the stock tires onto them. I can get a pic tomorrow if you'd like.
Thank you. I just had a quick look at the RPM Revolvers posted on ebay and it could be just what I'm looking for (cheap, chrome, similar in appearance to Bruiser wheel, etc.). However, apparently there are a few variations (82053,82063,82073, and 82233 - all in chrome) so I'll need to understand how they differ. I think Bruiser wheels are also 2.2 and I'll want Pro-Line Trenchers like the truck in the photo above. If you don't mind, could you please post a pic of your rig? thanks again.
therigliveson, thanks for the pic. Your truck looks awesome with those RPM Revolvers.
A little update: the HPI wheels have arrived and they look just like the photo I'd posted earlier -- chrome plating and overall quality are first rate! The fronts lightly interfere with the TF2's steering links so I'll switch to the thicker 5.5mm hexes that were also included with the TF2 kit. With the thicker hexes, there is no interference.
I can now go ahead and order the Pro-Line Trencher tires and finish the truck (it's been sitting in a box for 4 years ). Thanks everyone!!!
Hey guys! Years ago, I built an RC10 with the A&L C2 chassis set. I originally put a ProTech II on it with the rear of the body going over the top of the shock tower. I thought the body looked too high so I trimmed the back off to lower the body. It...
I'm wondering which bodies fit the Losi LXT. I got my hands on one but didn't have a body.
Last post
Because they're cheap on ebay ($14.97 delivered) I picked up a XXXT body to try. Using the two LXT mounts in the front and the singular mount on the shock tower in the rear, it fits nice. Gonna get the body painted up and I'll post pics.
I just dug up my RC10 #6011 from my parent's house. I haven't found a battery that fits the transverse battery cup holders. Does anyone have suggestions on what to use in these models?
I also need a new battery slant holder and door for the futaba...
Last post
If you remove the plastic end caps, just be sure to cover the battery ends so that they don't short out against the chassis. :wink:
That will fit the original RC10 with no mods to the cups or any mods for that matter? I can't seem to find any with a 134mm length.
Thanks
Last post
Hi, No I haven't checked out the Traxxas forum,But I will.I'm not into this speed thing seriously.Just playing with it.I'm more into the 1/4 scale than 1/10 scale.I get into these moods and switch back and forth between the two.I built the dragster...
Does anybody know if the Tamiya Alpine a110 body will fit on the M03R chassis?
I know the body was originally released on the M02 chassis with the front lay down shock. I was hoping it would cover the M03 chassis as well.
Also, has anybody here had...
Last post
Try the HPI Cup Racer for a 4wd mini, INFINITE adjustability, Mini bodies fit it. I love mine, it's the only thing other than AE that I drive alot.