Alloy Build (FINISHED) also, undecided on name.
- DMAT
- Approved Member
- Posts: 884
- Joined: Wed Mar 20, 2013 8:53 am
- Location: Baton Rouge, La
- Been thanked: 3 times
Alloy Build (FINISHED) also, undecided on name.
so I'm finally getting my build together. a majority of parts are put together so far. Its just a test fit for the moment until I decide how I want to have this all anodized. Most of the parts I've deanodized and polished up to a mirror finish. There is nothing under the gear cover at moment aside from the top shaft sticking out.
Parts:
-stock chassis (ebay)
-alloy stealth tranny & spacers (toyranosaurus aka REC)
-stock motor plate (ebay)
-stock nose plate (ebay)
-alloy front/rear arms (barts parts)
-alloy rear shock tower (ebay don anodizer)
-alloy 1.02 front shock tower (ebay one off)
-b4 front onboard carrier (STRC)
-b4 rear carriers (drilled to 1/8" hinge pin) (STRC)
-b4 caster blocks (drilled to 1/8" hinge pin) (STRC)
-b4 shock bushing (close but loose fit) (STRC)
-traxxas rustler heatsink plate (STRC)
-b4 shock bushing (STRC)
-shock spacers (used on shocks, not sure on vender)
-rc10gt shock set (ebay)
-crp esc mount tray (ebay)
-sees direction rims 2.0 x 1.5 fronts and rears (dad's & granddad's cars)
-protech stub axles in front (ebay, customized heavily)
-alloy front bulkheads (atlas)
-alloy rear arm mounts (atlas)
-alloy antenna mount (atlas)
-bell crank set (ebay)
-alloy body posts (ebay)
-b4 battery heatsink (Integy)(removed from build)
-thin walled 2x1 channel cut to length (unmounted at moment)
-alloy Gear Cover (Integy)
-stealth slipper hubs (ebay)
-4-40 rod ends (rc4wd, 4-40 rods need to be shortened to use)
-roll cage upper (BermudaCustomDesigns)
-roll cage panels (BermudaCustomDesigns)
-HG alloy differential gear (ebay)
-1/4" CVD axle kit (MIP)
-b4 Shiny CVD's (MIP)
-Bearings (avidrc)
-6.4 mm brake hose p clamps (ebay)
-stealth tranny brace (Dhood)
- rear bulkhead (jwscab)
-wing (chophead/pargustore)
-screws (stainless steel from fastenal)
-Exterior body panels were home made.
Gears
-alloy differential gear (HG)
-steel idler (Robinson racing)
-B4 top shaft
-SC10 87t spur gear (hot racing)
-varying pinion gears (Robinson racing)
electronics
Reciever: Futuba 603FS
Servo: Turnigy MG959
Motor: Velineon 3500
Battery: Venom 7.4 2s
Esc: Traxxas vxl 3s
Parts:
-stock chassis (ebay)
-alloy stealth tranny & spacers (toyranosaurus aka REC)
-stock motor plate (ebay)
-stock nose plate (ebay)
-alloy front/rear arms (barts parts)
-alloy rear shock tower (ebay don anodizer)
-alloy 1.02 front shock tower (ebay one off)
-b4 front onboard carrier (STRC)
-b4 rear carriers (drilled to 1/8" hinge pin) (STRC)
-b4 caster blocks (drilled to 1/8" hinge pin) (STRC)
-b4 shock bushing (close but loose fit) (STRC)
-traxxas rustler heatsink plate (STRC)
-b4 shock bushing (STRC)
-shock spacers (used on shocks, not sure on vender)
-rc10gt shock set (ebay)
-crp esc mount tray (ebay)
-sees direction rims 2.0 x 1.5 fronts and rears (dad's & granddad's cars)
-protech stub axles in front (ebay, customized heavily)
-alloy front bulkheads (atlas)
-alloy rear arm mounts (atlas)
-alloy antenna mount (atlas)
-bell crank set (ebay)
-alloy body posts (ebay)
-b4 battery heatsink (Integy)(removed from build)
-thin walled 2x1 channel cut to length (unmounted at moment)
-alloy Gear Cover (Integy)
-stealth slipper hubs (ebay)
-4-40 rod ends (rc4wd, 4-40 rods need to be shortened to use)
-roll cage upper (BermudaCustomDesigns)
-roll cage panels (BermudaCustomDesigns)
-HG alloy differential gear (ebay)
-1/4" CVD axle kit (MIP)
-b4 Shiny CVD's (MIP)
-Bearings (avidrc)
-6.4 mm brake hose p clamps (ebay)
-stealth tranny brace (Dhood)
- rear bulkhead (jwscab)
-wing (chophead/pargustore)
-screws (stainless steel from fastenal)
-Exterior body panels were home made.
Gears
-alloy differential gear (HG)
-steel idler (Robinson racing)
-B4 top shaft
-SC10 87t spur gear (hot racing)
-varying pinion gears (Robinson racing)
electronics
Reciever: Futuba 603FS
Servo: Turnigy MG959
Motor: Velineon 3500
Battery: Venom 7.4 2s
Esc: Traxxas vxl 3s
-
- Approved Member
- Posts: 942
- Joined: Wed Aug 07, 2013 5:25 am
- Location: Oregon Coast
- Has thanked: 100 times
- Been thanked: 206 times
Re: Alloy Build (test fit)
Dittofoots wrote:Daauummmm!
Losi - Jrx2, Pro, Jr2, Pro SE, JrxT, JrT, LXT, NXT, XXKE, XXTG+
Mini - T, LST, LST2, Crawler
Micro - Trekker, SCT, T
Crawlers - Trx4 Defender, Bootleg Bruiser Shelf Queen
-Bashers under contruction- Jrx2
Mini - T, LST, LST2, Crawler
Micro - Trekker, SCT, T
Crawlers - Trx4 Defender, Bootleg Bruiser Shelf Queen
-Bashers under contruction- Jrx2
- integra22t
- Approved Member
- Posts: 637
- Joined: Fri Aug 09, 2013 1:36 pm
- Location: Kingston On.Ca
- Been thanked: 2 times
Re: Alloy Build (test fit)
WOW it reminds me of the liquid metal termantor .. what kind of rims are you thinking ?
- flipwils11
- Approved Member
- Posts: 1904
- Joined: Sun Feb 14, 2010 10:30 pm
- Location: St Paul, MN
- Been thanked: 15 times
- DMAT
- Approved Member
- Posts: 884
- Joined: Wed Mar 20, 2013 8:53 am
- Location: Baton Rouge, La
- Been thanked: 3 times
Re: Alloy Build (test fit)
all those seeming stupid tech threads had to add up to something. I know I couldnt do some of this stuff without y'all knowledge.
- shodog
- Approved Member
- Posts: 3816
- Joined: Thu Oct 05, 2006 3:09 pm
- Location: Washington
- Has thanked: 3 times
- Been thanked: 86 times
Re: Alloy Build (test fit)
Holy hell that is awesome. You got everything polished up like chrome. Nice job.
- hawgfanman
- Approved Member
- Posts: 279
- Joined: Sat Dec 10, 2011 3:05 pm
- Location: Midlothian, TX
- Has thanked: 13 times
- LosiXXkid
- Approved Member
- Posts: 757
- Joined: Sun Mar 03, 2013 5:35 pm
- Location: Islington, North London
- Has thanked: 2 times
- Been thanked: 6 times
Re: Alloy Build (test fit)
...oh yes, the Cyberdyne Systems prototype T-1000 made from mimetic poly-alloy....integra22t wrote:WOW it reminds me of the liquid metal termantor .. what kind of rims are you thinking ?
~I'm a lot older now than I was then and wish that I knew then what I know now~
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 9 Replies
- 2097 Views
-
Last post by THUNDERSTRIKE1
-
- 1 Replies
- 576 Views
-
Last post by DennisM
-
- 62 Replies
- 6749 Views
-
Last post by Diamond Dave
-
- 6 Replies
- 926 Views
-
Last post by GJW
-
- 38 Replies
- 9156 Views
-
Last post by limestang
-
- 0 Replies
- 1360 Views
-
Last post by photogRC
-
- 15 Replies
- 2532 Views
-
Last post by Caine
-
- 18 Replies
- 2311 Views
-
Last post by Welshy40
Who is online
Users browsing this forum: Google [Bot] and 34 guests