Pinion Gear Suggestions for T3 Brushless Set Up

Moderators: scr8p, klavy69

3 posts • Page 1 of 1

erichevy: Approved Member; Posts: 159; Joined: Thu Oct 16, 2014 1:37 pm; Location: Marshall MI; Has thanked: 2 times; Been thanked: 8 times

Pinion Gear Suggestions for T3 Brushless Set Up

Quote

Post by erichevy » Thu Jan 21, 2016 9:24 am

My son has an Associated T3 with the stock 87t gear. We are running a 3300kv brushless motor and 2S lipo. I was looking for recommendations/starting points on what size pinion to use with this set up. The truck is all stock. Thanks in advance.

erichevy: Approved Member; Posts: 159; Joined: Thu Oct 16, 2014 1:37 pm; Location: Marshall MI; Has thanked: 2 times; Been thanked: 8 times

Re: Pinion Gear Suggestions for T3 Brushless Set Up

Quote

Post by erichevy » Fri Jan 22, 2016 9:23 pm

I went with an 81t gear and 19t pinion to start. Based on what I found on this site, 81 / 19 X 2.40 (T3 Transmission), I end up with a FDR of around 10.2. With the 3300kv brushless and 2S LiPo, it is plenty fast enough for my 13 year old.

pumpkinfish: Approved Member; Posts: 263; Joined: Wed Nov 06, 2013 8:01 am; Location: Schwenksville, PA

Re: Pinion Gear Suggestions for T3 Brushless Set Up

Quote

Post by pumpkinfish » Fri Feb 05, 2016 12:32 pm

I use this chart for starting gearing and adjust as needed on track.

http://teamnovak.com/tech_info/view_article/26

Post Reply

3 posts • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

6 gear trans rebuild what was the stock pinion and spur gear

Last post by jackflak « Fri Nov 08, 2013 7:00 pm
Posted in RC10 Buggy Forum

by jackflak » Fri Nov 08, 2013 7:00 pm » in RC10 Buggy Forum

I know the 6 gear trans has a much different pitch than my stealth trans. Can someone please tell me what the original tooth count and pitch should be for the pinion and spur gears? Also where can I buy snap ring pliers small enough for the tiny...

0 Replies

979 Views

Last post by jackflak
Fri Nov 08, 2013 7:00 pm
What size pinion gear and spur gear?

Last post by JK Racing « Tue Mar 13, 2012 11:55 pm
Posted in RC10 Buggy Forum
Replies: 6
by mikea96 » Mon Mar 12, 2012 11:22 pm » in RC10 Buggy Forum

First post

So what size pinion and spur should i run in my gold pan buggy with stealth tranny and a Reedy Sonic 13.5 brushless?

Last post

No boost 17.5 I was running 33/69 :)

No boost 13.5 I would drop about 4-5 teeth (so 28-29)...same range that Reggie said.

6 Replies

1940 Views

Last post by JK Racing
Tue Mar 13, 2012 11:55 pm
[Still Valid]1:1 car wheel set shipping to WE - suggestions?

Last post by Lonestar « Mon May 26, 2014 11:32 am
Posted in Off-Topic / Chit-Chat
Replies: 9
by Lonestar » Tue May 13, 2014 10:23 am » in Off-Topic / Chit-Chat

First post

Hi Guys, I have a non-RC question which some of the many (full size!) car buffs on the forum might be able to help with... i located a set of four nice rims for my car in the US via ebay... but I live in Western Europe. The seller, who posted his ad...

Last post

I've bought a lot of used JDM and EDM Honda Civic parts from all over the world, and the sellers always shipped DHL. Nothing as large or heavy as wheels, though.

I had fragile 25+ year old plastic lights and thin metal window visors arrive without...

9 Replies

712 Views

Last post by Lonestar
Mon May 26, 2014 11:32 am
Brushless motor turn suggestions

Last post by HotRod716 « Sat Nov 21, 2015 8:13 am
Posted in Yokomo Forum
Replies: 4
by HotRod716 » Tue Nov 17, 2015 6:38 am » in Yokomo Forum

First post

Hello to all:

I am getting back into the hobby after 25 year hiatus. I am giving my daughter a sc10 (brushed rtr) and I thought it would be great to go to the local track, short corse with many tight turns, and run my old Kokomo. After reading up...

Last post

Thanks for the replies. I'm going with a trinity 13.5t and see how it goes. I have to wait until Christmas before I can tear her apart. Have to hide this car from my daughter so she doesn't suspect anything.

4 Replies

1157 Views

Last post by HotRod716
Sat Nov 21, 2015 8:13 am
RC10T Brushless Gearing Suggestions

Last post by i crash cars « Mon Sep 10, 2018 11:28 am
Posted in Modern Electronics
Replies: 3
by i crash cars » Fri Sep 07, 2018 12:08 pm » in Modern Electronics

First post

Could use your guys help with how I should gear my truck now that I went brushless.

Motor: Turnigy Trackstar Outlaw 13.5T (2886KV)
Trans: Stock stealth with the B4 Slipper mod
Tires: HPI Yokohama Geolandar (4.05 diameter)

Some initial research has...

Last post

Ok thanks guys!

3 Replies

1773 Views

Last post by i crash cars
Mon Sep 10, 2018 11:28 am
EZRUN 3000kv brushless spur/pinion combo?

Last post by JK Racing « Thu Aug 04, 2011 10:42 pm
Posted in Modern Electronics
Replies: 1
by Mattwarner » Mon Aug 01, 2011 5:57 am » in Modern Electronics

First post

Hi,

Iam restoring my vintage RC10 Graphite and have just ordered an EZRUN 3000kv brushless and ESC Combo, its only going to be used for a bit of fun and i am only looking at using some 3800mah NIMH rather than LIPO's.

I have a load of spare spurs...

Last post

6 gear or Stealth?

6 gear, start with 16-17 pinion to 86-87 spur

stealth, start with 18-19 pinion to 81 spur

1 Replies

550 Views

Last post by JK Racing
Thu Aug 04, 2011 10:42 pm
Can I use this gear and pinion

Last post by Jay Dub « Sun Dec 09, 2012 1:34 pm
Posted in RC10 Buggy Forum
Replies: 7
by bow2986 » Thu Dec 06, 2012 9:08 pm » in RC10 Buggy Forum

First post

Hi fellas, I am so new to rc cars so this might sound stupid , I normally fly rc helis but it's nearly allways to windy so I purchased a rc10, its not my first rc car , that was a super champ back in the 80's.....but it's definitely my fav. I am...

Last post

Post pics of the underside of the rear of your chassis. Many of the late 6 gear cars also had holes for the stealth tranny (which may be the xtras holes you speak of). As far as gearing is concerned, you are in a good range for that car and motor...

7 Replies

1651 Views

Last post by Jay Dub
Sun Dec 09, 2012 1:34 pm
lunchbox pinion gear???

Last post by losiXXXman « Wed Jan 05, 2011 4:42 pm
Posted in Tamiya Forum
Replies: 10
by vintage88 » Mon Jan 03, 2011 7:49 pm » in Tamiya Forum

First post

are there different gears you can use??? and what pinion do i need???

thanks everyone

Last post

Tim... I have that pinion around, so don't gp buying one if you haven't.. Sorry I didn't think about/remember to get it for you.

10 Replies

3031 Views

Last post by losiXXXman
Wed Jan 05, 2011 4:42 pm

Return to “RC10 Truck Forum”

Who is online

Users browsing this forum: Google Adsense [Bot] and 7 guests

Pinion Gear Suggestions for T3 Brushless Set Up

Pinion Gear Suggestions for T3 Brushless Set Up

Re: Pinion Gear Suggestions for T3 Brushless Set Up

Re: Pinion Gear Suggestions for T3 Brushless Set Up

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online

Login Register