Kranzel's wheel spacer

Moderators: scr8p, klavy69

Post Reply

16 posts

scr8p: Administrator; Posts: 16540; Joined: Tue Feb 07, 2006 9:46 pm; Location: Northampton, PA; Has thanked: 28 times; Been thanked: 976 times

Re: Kranzel's wheel spacer

Quote

Post by scr8p » Tue Feb 09, 2010 2:49 pm

i used a low profile 8-32 nut.

Flashback R/C Products

My Gallery

Post Reply

16 posts

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Rear wheel spacer alternative

Last post by radioactivity « Thu Aug 20, 2020 9:40 am
Posted in RC10 Buggy Forum
Replies: 7
by radioactivity » Wed Aug 19, 2020 1:20 pm » in RC10 Buggy Forum

First post

With my last small parts order I got some 91633 FT 12mm piston (V2) blank TP cheap on Ebay. Like $6 for 4 12mm pistons.
The price of 9608 spacers, when you find them, is $20 to $25 per pair if not more.
The thought was @ $3.00 per pair I might drill...

Last post

They fit 3/16 AE axle cars such as...

From factoryworksrc

Chuck

7 Replies

1396 Views

Last post by radioactivity
Thu Aug 20, 2020 9:40 am
R&D/Kranzel Terminator (2.25)

Last post by MarkyDents « Fri Aug 26, 2022 7:43 pm
Posted in Other Makes/Models
Replies: 26
by MarkyDents » Sat Jan 01, 2022 10:11 pm » in Other Makes/Models
1

2
First post

3C47DA92-634D-43AB-81D7-4A69FE422999.jpeg 76B7DBDD-6A44-457C-8C94-6DDB7FF2E27E.jpeg
I’d really like to outfit this properly.

Last post

That's a Dahm good possibility.

:lol: NICE :D
The first clue for me was the billboard size decal :wink:
26 Replies

2839 Views

Last post by MarkyDents
Fri Aug 26, 2022 7:43 pm
Rc10 kranzel modified oval

Last post by PBR Allstar « Fri Jan 15, 2010 1:56 pm
Posted in RC10 Buggy Forum
Replies: 11
by reign79 » Thu Jan 14, 2010 6:42 pm » in RC10 Buggy Forum

First post

Well as if i dont have enough builds i got bored waiting on some stuff so i got started on another :roll: Just finished sanding and repainting the chassis and got the front end together not sure what direction this one is going any suggestions?

Last post

did you buy that bulkhead from me? i had one, but don't remember who i sold it to.

No, that one was off my R&D that I had years ago.

11 Replies

1033 Views

Last post by PBR Allstar
Fri Jan 15, 2010 1:56 pm
Motor Spacer

Last post by Chris00gt « Fri Nov 01, 2013 2:05 am
Posted in Temple's RC10 Tech Forum
Replies: 6
by DMAT » Tue Oct 29, 2013 4:53 pm » in Temple's RC10 Tech Forum

First post

So I need to pull the motor I have slightly back off the motor plate so the shaft doesnt hit the gear cover. My normal thought would be to just use washers but I dont know if that will end badly or not.

Any suggestions or just go with it?

Last post

Trinity use to make the heat sink motor spacer. I have one on my worlds car from back in the day. Very rarely see them on e-bay.

6 Replies

1058 Views

Last post by Chris00gt
Fri Nov 01, 2013 2:05 am
jrx2 axle spacer

Last post by y2kgtp « Fri Jan 30, 2009 11:12 am
Posted in Losi Forum
Replies: 7
by lostwages » Fri Jan 30, 2009 3:32 am » in Losi Forum

First post

anybody have a pic and measurements for the spacer between the rear hub bearing and the drive pin? mine are missing and i might make a few on my lathe, thanks.

Last post

$2 for 2
I made some out of aluminum tubing from the lhs. Not as pretty as the factory ones, but for the same $2 I got enough tubing to make a ton of these

I think I will find some tubing as well... :lol:

7 Replies

1059 Views

Last post by y2kgtp
Fri Jan 30, 2009 11:12 am
What is this, stealth right diff spacer #4452?

Last post by isobarik « Mon Feb 23, 2015 6:01 am
Posted in Associated On-Road Forum
Replies: 4
by RCveteran » Thu Nov 18, 2010 1:59 pm » in Associated On-Road Forum

First post

Cleaning out the closet and in the waht the heck is this mode?

Last post

For a while there was a diff. for the 1:12 cars called the stealth as well. The RC12LC has it standard.

there where actually 2 stealth diffs the stealth diff and the stealth diff II

the first one was used with standard wheels
the stealth II was...

4 Replies

1006 Views

Last post by isobarik
Mon Feb 23, 2015 6:01 am
Alternative to 9608 blue spacer

Last post by juicedcoupe « Sat Jan 30, 2021 12:22 am
Posted in Temple's RC10 Tech Forum
Replies: 1
by radioactivity » Fri Jan 29, 2021 11:27 pm » in Temple's RC10 Tech Forum

First post

Really haven't been able to find any Associated FT Rear Axle Wheel Spacers, at least reasonably.
Yep, a 2mm washer will work but it isn't too pretty and doesn't have a taper to prevent rubbing the outer portion of the bearing.
So I bought Durango...

Last post

The Ebay store is hit and miss, but he has them.

1 Replies

510 Views

Last post by juicedcoupe
Sat Jan 30, 2021 12:22 am
LOSA2024 Rear Shock Tower Spacer

Last post by 66intheSky « Fri Jun 25, 2010 11:09 am
Posted in Losi Forum
Replies: 4
by 66intheSky » Sat Jun 19, 2010 11:37 am » in Losi Forum

First post

Anybody know what this spacer was for and why? There is no mention of it in my original JRX2 manual.

Thanx

Last post

Gotcha......Thanx again.

4 Replies

607 Views

Last post by 66intheSky
Fri Jun 25, 2010 11:09 am

Return to “Temple's RC10 Tech Forum”

Who is online

Users browsing this forum: No registered users and 7 guests