Correct. It's obvious that this seller is a dirt oval guy, where mid-motor chassis setup is very common. We run our B3 gearboxes reversed in all of our cars on high-bite tracks.
Where were they? I think I might have remembered that... I musta TOTALLY missed that one. Can you find the ad? I searched there and found nothing similar.
Asso_man! wrote:the shaft can be placed both on the right and left sides of the tranny, like the original Stealth...
Ah, that makes sense. I kinda remember that now that you mentioned it. I was racing Kyosho's back when the rc10 came out so I wasn't really up on them. Didn't get any Associated stuff till about 2000. Still trying to catch up on all the old stuff. Thanks.....
MelvinsArmy wrote:I just need to get off my lazy butt, sell some mannequin hands to fund it and get it done.
That just sounds so weird.
I just happened to catch the TV show "how it's made" the other night, they were showing how they made mannequin's. The funniest thing was that they blurred out the foam boobs.
That's hilarious. I spent about 6 years working in a mannequin factory. I painted their faces. I've got a HUGE collection of hands that I've been slowly selling off on ebay.
Well hmm. I'm trying to think of a hint that won't give it away. Think RC10, lots of awesome parts, some custom made just for this project and think baja/sand dune vehicle. That's all I can say for now, because it's really still in it's infancy. Well, most of the parts are gathered, just not the most important one.
The tranny arrived today. It looks pretty awesome, a nice piece of aluminum. No markings at all, so it's origins remain a mystery. Definately one of my best pieces now.
I got my worlds today so I figured it would be a good time to figure out wtf Associated did. I have three scenarios all played out
-stock worlds case and idler
-6565 case with worlds idler and extra bearings
-6565 case and 6570 idler (aka how it...
Last post
I'm in the middle of building a worlds car too. Mine seemed to have a bad top shaft. I put one in from an old T4 transmission I had laying around and viola! Smooth operation.
Overall, I'm a little disappointed at the quality of the materials...
Hey guys,
Love the forum but I couldn't find anything on this topic? I recently purchased both a original RC10 and a RC10CE. The RC10CE I plan to use as a vintage racer however it doesn't have a transmission. Will a B3 Stealth transmission work as...
Last post
Nah you'd just have to cut out a bit between the 2 bulkhead screws, the trans is narrow enough to fit between them and leave plenty of meat around the screws.
Hello all. I was wondering if anyone knew of any online retailers that still stock parts for the 2.25 stealth tranny? I looked at another post on this forum that had some links to Tower Hobbies and I searched tower but to no avail.
So the question here is durability. I'm looking at a trinity d5 flatliner motor for my car. It's the 8 turn version and It's brand new. My question is if my first generation stealth transmission will handle the power and torque of the motor? I don't...
Last post
A new can?? I would be more worried about the armature being burnt from the heat even though it looks just fine to me. So would any mod can work? This motor looks to be about the size of I believe a 380. I'm not really sure. Also how would I handle...
What is the difference between the original stealth tranny and the T2/T3 tranny? I have been told it’s the gear case and the diff gear? Is that the same as a Losi XXX-T too?
Last post
yes they are all similar in being three gear, but more than half of parts are different. Different trans case, diff gear, rings, idler gear, motor plate. The top shafts can swap; bearings, diff balls and thrust assembly also all cross between...
what was this used for there? i picked that one on ebay recently and was wondering what that ratio was used for
Last post
so, did i do it right this time?
you know, the little hissy fits you throw everytime someone says something you don't like is getting kinda old. i'll be the first to admit that you were right, though. i took my time on this one, and didn't need to...
What Brushless could i run in my rc10t without the slipper melting?
I've got an ez run 8.5t or the RTR brushless out of my B4.1 just dont want anything bad to happen!
On the hunt for parts to do the topshaft conversion so i wont have this problem...
Last post
Was just thinking about asking the same question, the gearbox is fitted with the b4 slipper and topshaft gonna try my b4.1 stock brushless in it first then try the 8.5 ezrun. i have a feeling she will fly!