RC10 XXX worlds ( REVISION & RECHASSIS )

[Charlie don't surf]

I'll post a pic of a dremel based handheld router used, very simple

[fastang]

I'll post a pic of a dremel based handheld router used, very simple

Wasn't there a pattern for cutting the chassis as well? I am doing a similar project and could use it if anyone has it.

BTW, I could also use the trace of the top deck I asked you about in a previous post too!

Thank you much

[Charlie don't surf]

Yes, I'll get up with you on the topdeck tracing in about a week, when I get back home

[Charlie don't surf]

I'll post a pic of a dremel based handheld router used, very simple

Wasn't there a pattern for cutting the chassis as well? I am doing a similar project and could use it if anyone has it.

BTW, I could also use the trace of the top deck I asked you about in a previous post too!

Thank you much

Hey, I forgot all about this, can you remind me via PM regarding the top deck tracing you needed--I can send it along with the spur--




and..........quick update--I am trying to get all RPM parts on this car (except for the battery cup) so I mounted a set of RPM rear truck posts to the top of the bellcranks (drilled & tapped for 8/32) which also solved the problem of a front body mount, which the bulkhead dosen't have-

1 reggies XXX worlds 001.jpg

Then I used the front RPM truck post in the rear , also I was going to put a set of Tecnacraft turnbuckles on this car, but
I put a RCPS on, and it just looks more manly!, so that will get changed as well--

1 reggies XXX worlds 002.jpg

[JPAE07]

Looks good so far.

[SteveK]

I'd like to see pics of the Dremel router setup as well. I'm going to pick up their router table kit soon. Right now I just rough out parts with a large cutoff wheel and grinding down to get it close. Hopefully the router table setup will help get a little more precise.

Until I get around to building that CNC router.

[Charlie don't surf]

Ok, here we go--got bored today--and I wanted to show the simple system I use for small parts-

1 reggies XXX worlds 004.jpg

1/8 rotozip tile bit ( a little longer than what I normally use) with and "e" clip on the tool surface to act as a bearing retainer, then 4 flanged pan car 1/8" x? bearings to use as a guide

1 reggies XXX worlds 005.jpg

scrawled the lines in the donor chassis for the part

1 reggies XXX worlds 006.jpg

after making some "plunge" holes
for the tool to drop into I run the cutting bit along the rip fence, in this case the short portion of a 4' t square, clamping the straight edge in place

1 reggies XXX worlds 007.jpg

the almost finished part, I still need to drum sand the inside radius portion of the part, as well as the outside corners to finish it.

Too bad once I got this far I decided that the fiberglass one looked better on the car!, oh well

[slotcarrod]

That is a very cool router bit you built, not to mention, the car is very nice as well!

[Charlie don't surf]

I've been driving myself nuts for a year trying to find these. All of you I didn't ask feel free to tell
me how many NIP you would have sold me, now that I have em!

[Bormac]

Yeah nice tyres for anyone that needs to find 2.1inch rubber. LOL! I have a set on the front of my Cougar2000 and also another nip set I found a while back. definately the best 2.1 fronts you'll find i think.

[slotcarrod]

I've been driving myself nuts for a year trying to find these. All of you I didn't ask feel free to tell
me how many NIP you would have sold me, now that I have em!

Hi Reg

Do you need another set? If so I have a NIP that I will never use, LMK!

Good to have you back, we missed you, hope your vacation was good! Nice panties BTW!

Rod

[Charlie don't surf]

See I knew it would happen!! Yes --I need to send those gear covers to you as well, yes vaca was nice--lots of texts from members asking if I died or something the only bad thing was this goofy Canadian fellow kept looking up my skirt

[mikea96]

I need a new set of these tires if someone has a set they want to get rid of.

[slotcarrod]

See I knew it would happen!! Yes --I need to send those gear covers to you as well, yes vaca was nice--lots of texts from members asking if I died or something the only bad thing was this goofy Canadian fellow kept looking up my skirt

Blame Canada! More like cough scr8p cough!

Small box on the way today! We allll like small boxes!

[vintage AE]

very nice work reg, as always! I love all the white RPM parts with the graphite chassis, modified to boot).

as for the goofy canadian...it wasn't me either. glad to hear you had a good one.