My first RC10 Gold Pan Project
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
So how's the restore coming along on this bad boy?
I don't suppose you are going to manage to be able to get me the spring cup dimensions I asked for, before you sell them, are you?
Shouldn't be to hard to spin a pair of these up on a lathe...
I don't suppose you are going to manage to be able to get me the spring cup dimensions I asked for, before you sell them, are you?
Shouldn't be to hard to spin a pair of these up on a lathe...
Re: My first RC10 Gold Pan Project
Yeah, no measuring...they fit the bottom of the rear shock, thats about how big they areDr. Robotnik wrote:So how's the restore coming along on this bad boy?
I don't suppose you are going to manage to be able to get me the spring cup dimensions I asked for, before you sell them, are you?
Shouldn't be to hard to spin a pair of these up on a lathe...
I couldnt measure some of those dimensions correctly.
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
Lol seriously? I don't have the big bucks these are going to go for on ebay so you're not missing out on my money in the auction. But I can paypal you money for a ruler if you'd like?Dogbone wrote: Yeah, no measuring...they fit the bottom of the rear shock, thats about how big they are
I couldnt measure some of those dimensions correctly.
Just the outside dimensions would be great so I can get them in proportion would be fantastic. Those are dimensions A and I.
Anything else would be great too obviously but I could probably guess. I can send you some RC10 parts you might need in thanks...anyway good luck with the auction.
Re: My first RC10 Gold Pan Project
LOL, I wasnt trying to make you bid...I just didnt think I could get those inside numbers correct enough.Dr. Robotnik wrote:Lol seriously? I don't have the big bucks these are going to go for on ebay so you're not missing out on my money in the auction. But I can paypal you money for a ruler if you'd like?Dogbone wrote: Yeah, no measuring...they fit the bottom of the rear shock, thats about how big they are
I couldnt measure some of those dimensions correctly.
Just the outside dimensions would be great so I can get them in proportion would be fantastic. Those are dimensions A and I.
Anything else would be great too obviously but I could probably guess. I can send you some RC10 parts you might need in thanks...anyway good luck with the auction.
Outside Dia 11/16"
height 1/4"
Wall thickness 1/32"
Inside perch dia 3/8"
bottom spring rest pad "about 1/16"
Inner hole small "shock shaft"
Inner hole large "lower shock mount"
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
Thanks a lot mate, I can now make a set up in the lab at work, for my runner and have it looking pretty sweet!
P.S. Was just kidding about the bid thing
P.S. Was just kidding about the bid thing
Re: My first RC10 Gold Pan Project
But were you kidding about sending parts? I think I need a NIB RC10 shipped overnightDr. Robotnik wrote:Thanks a lot mate, I can now make a set up in the lab at work, for my runner and have it looking pretty sweet!
P.S. Was just kidding about the bid thing
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
Hahaha, no I wasn't (I was offering some bits and bobs I might have to keep yours going) but I don't have a NIB RC10 and if I did, I'd build it!Dogbone wrote:But were you kidding about sending parts? I think I need a NIB RC10 shipped overnightDr. Robotnik wrote:Thanks a lot mate, I can now make a set up in the lab at work, for my runner and have it looking pretty sweet!
P.S. Was just kidding about the bid thing
Re: My first RC10 Gold Pan Project
Good luck with the build. I am in the same boat, and ready to work on mine.
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
Thanks for the dimensions mate I made 4 pairs today on my lunch break (and by that I mean my boss is away so I started working on these at 9 and finished at 12, these are a pig to make and I had to make a tool to cut the inside piece out )Dogbone wrote: Outside Dia 11/16"
height 1/4"
Wall thickness 1/32"
Inside perch dia 3/8"
bottom spring rest pad "about 1/16"
Inner hole small "shock shaft"
Inner hole large "lower shock mount"
BTW how's the restoration going? Post pics or it never happened
Re: My first RC10 Gold Pan Project
i want to see them, please post some pics when the camera is working!Dr. Robotnik wrote:Thanks for the dimensions mate I made 4 pairs today on my lunch break (and by that I mean my boss is away so I started working on these at 9 and finished at 12, these are a pig to make and I had to make a tool to cut the inside piece out )Dogbone wrote: Outside Dia 11/16"
height 1/4"
Wall thickness 1/32"
Inside perch dia 3/8"
bottom spring rest pad "about 1/16"
Inner hole small "shock shaft"
Inner hole large "lower shock mount"
BTW how's the restoration going? Post pics or it never happened
Re: My first RC10 Gold Pan Project
Pics were in another thread, but here ya go.
- Attachments
-
- 08f9_12.jpg (87.27 KiB) Viewed 706 times
- 08f9_12.jpg (87.27 KiB) Viewed 706 times
-
- 08b1_12.jpg (79.18 KiB) Viewed 704 times
- 08b1_12.jpg (79.18 KiB) Viewed 704 times
-
- Untitled-16.jpg (106.14 KiB) Viewed 702 times
- Untitled-16.jpg (106.14 KiB) Viewed 702 times
-
- Untitled-15.jpg (118.35 KiB) Viewed 703 times
- Untitled-15.jpg (118.35 KiB) Viewed 703 times
-
- Untitled-10.jpg (116.52 KiB) Viewed 702 times
- Untitled-10.jpg (116.52 KiB) Viewed 702 times
-
- Untitled-1.jpg (79.56 KiB) Viewed 700 times
- Untitled-1.jpg (79.56 KiB) Viewed 700 times
-
- Untitled-5.jpg (95.03 KiB) Viewed 701 times
- Untitled-5.jpg (95.03 KiB) Viewed 701 times
Re: My first RC10 Gold Pan Project
umm... thanks but i was talking to DR robo bout his cups he made. you should delete those pics to avoid taking up bandwidth... nice job on the restoration though!
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
Nice restoration dogbone, I must have brain farted as I saw those in another thread maybe I coudn''t believe it was the same carasashaw wrote:i want to see them, please post some pics when the camera is working!Dr. Robotnik wrote:Thanks for the dimensions mate I made 4 pairs today on my lunch break (and by that I mean my boss is away so I started working on these at 9 and finished at 12, these are a pig to make and I had to make a tool to cut the inside piece out )Dogbone wrote: Outside Dia 11/16"
height 1/4"
Wall thickness 1/32"
Inside perch dia 3/8"
bottom spring rest pad "about 1/16"
Inner hole small "shock shaft"
Inner hole large "lower shock mount"
BTW how's the restoration going? Post pics or it never happened
I will take pics of what I have made asap Asa, I borrowed a camera last night and its batteries failed halfway through taking pics and I hadn't got to taking pics of the spring cups. I am seriously considering buying a camera for xmas
- Asso_man!
- Approved Member
- Posts: 3959
- Joined: Thu Aug 03, 2006 7:49 am
- Location: EU
- Has thanked: 40 times
- Been thanked: 70 times
Re: My first RC10 Gold Pan Project
ED, if ever you make some more repos of these, I would be very very interested in buying a couple of pairs from you
_____________________________________________
_____________________________________________
Come and visit the stable
_____________________________________________
Come and visit the stable
- Dr. Robotnik
- Approved Member
- Posts: 1442
- Joined: Wed Oct 11, 2006 11:05 am
- Location: Nutterham, United Kingdom
- Been thanked: 2 times
Re: My first RC10 Gold Pan Project
Hahaha edit that to say Ed (long story about family not using first names ) and we have a dealAsso_man! wrote:ED, if ever you make some more repos of these, I would be very very interested in buying a couple of pairs from you
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 1 Replies
- 876 Views
-
Last post by rc-10 gold pan
-
- 1 Replies
- 904 Views
-
Last post by limestang
-
- 28 Replies
- 4768 Views
-
Last post by Tamlok
-
- 3 Replies
- 960 Views
-
Last post by DarthRacer
-
- 20 Replies
- 2807 Views
-
Last post by REMJ666
-
- 18 Replies
- 2602 Views
-
Last post by Lonestar
-
- 29 Replies
- 3835 Views
-
Last post by vsefiream
-
- 13 Replies
- 1077 Views
-
Last post by smurf420
Who is online
Users browsing this forum: DotNetDotCom.org [Bot], sixdub and 37 guests