I offer a challenge...

[highwayracer]

I'm in...I'll try to use all of the parts (except wheels and tires) from the rc10 series.

highwayracer

[gmc572]

alright i,m a 1/4 of the way there(so far i think it will pass as a puller LOL!!!!) Who's got a tranny i can borrow!!(JOKING)

[highwayracer]

I'm about 1/2 way there. I've already figured out how to do everything...I just need to bolt everything up.

There are only 2 parts I need to fabricate to get this thing completed (front hub carrier & extension to mount chassis to front bulkhead). I know I probably went the easy route, but I wanted to keep my build limited to rc10 (10t) parts only. In addition, I need all of these parts for other builds...so I couldn't permanently alter these parts (except for the front nose plate).

I went with the following:
10t arms all around
12 gear transmission....2x6 gear
tmaxx wheels and tires (for now)
reverse rotation motor for the front (I didn't want to cut the motor plate)

Regards,
highwayracer

rc10 monster truck.jpg (93.51 KiB) Viewed 899 times

rc10 monster truck.jpg (93.51 KiB) Viewed 899 times

[Mr. ED]

I once had an ultima outfitted with clodwheels. it used RC10T tires. I guess it wouldn't count anyway
Don't have pics of it either and it was 2WD. Given up after I realised i didn't have a suitable servo

Edit: still have it but with just slightly larger tires than stadium truck. I compensate the higehr end-ratio by using an 8 cell batterry and a stock 540. still flies.

Highway racer: you could go with a hyperdrive belt conversion upfront if you want to avoid the reverse moter thing.

Or: check out the corally touring car with its 42 teeth diff-pulley. it's the m3 standard so just need to find a uitable belt and pinion pulley. Might be hard to match the eaxact same for the rear part. Maybe a one-way upfront so the front would only be pulling when needed?

nice challenge here
If I had a tub I'd be tempted to join in

[Tadracket]

Oh, you guys are way ahead of me. I guess I gotta get rolling.

[Mr. ED]

I wonder where high-way racer is gonna put the steering???

[Erich Reichert]

hmm.......................

i wish i had a set of those gold imex rims.

these?

http://cgi.ebay.com/GOLD-IMEX-VINTAGE-RC10-RIMS-ASSOCIATED-RC10-TIRES_W0QQitemZ320213017109QQihZ011QQcategoryZ34063QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

Sorry, bad joke.

And a repost to boot (see bottom of page 1)

While we're on these rims.. I NEVER DO THIS but these ones i really need... I'm throwing myself at all your mercy. I actually REALLY need those wheels for a project that is OVER THE TOP... trust me you guys will flip. Would you all mind laying off those... if anyone wanted them? I know its a dick move but like I said i never do this and i figured doesn't hurt to ask. Thanks

[Halgar]

Would you all mind laying off those... if anyone wanted them?

Mine!!! All mine!!!!

[Erich Reichert]

One, two, three SHOOT!!! (rock)

[Halgar]

(paper)

[highwayracer]

I wonder where high-way racer is gonna put the steering???

I could easily mount it in the stock location if I cut the front (rear) bulkhead. But since I don't want to alter the parts, I will be mounting the stock bell cranks in a slightly different location...one of the pieces that I have to fabricate.

I'll see if I can finish everything tonight.

Regards,
highwayracer

[Erich Reichert]

(paper)

DAMN!!! I knew you were gonna go paper!

[Halgar]

(paper)

DAMN!!! I knew you were gonna go paper!

I am the champion, my fre-end ...

[Erich Reichert]

she no work!

BTW you wouldn't BELIEVE the desicions that have been made by me using rock paper scissors

[Halgar]

Better? Clodtalk has all kinds of great smilies, I don't know why Bill hasn't installed them here too.

I hear ya on the decisions. Many a time a flip of a coin has made the choice for me. I only use rock/paper/scissors for really important stuff!