CW Dominator tech question....

General info, Q&A.

Moderators: scr8p, klavy69

User avatar
Brandon G
Approved Member
Posts: 2106
Joined: Mon Oct 01, 2007 8:23 pm
Location: Nashville, TN
Been thanked: 3 times

CW Dominator tech question....

Post by Brandon G »

Does the hub for the Dominator have the same screw spacing as a RC10L rear wheel?








I hope so... :wink:

Dirtdiver
Approved Member
Posts: 458
Joined: Sat Aug 01, 2009 6:27 pm
Location: CT, USA

Re: CW Dominator tech question....

Post by Dirtdiver »

I believe so.

Last year, I purchased a dominator and was given a NIP set of RC-10L rims. I never tried them out but assume that was the reason why they were in the box.

User avatar
scr8p
Administrator
Posts: 16699
Joined: Wed Feb 08, 2006 2:46 am
Location: Northampton, PA
Has thanked: 29 times
Been thanked: 1137 times

Re: CW Dominator tech question....

Post by scr8p »

they're the same as yokomo hubs. pan car rims should not fit. the scew holes are farther apart.

User avatar
Eau Rouge
Approved Member
Posts: 2224
Joined: Sun Jul 30, 2006 3:59 am
Location: Aurora, Illinois
Has thanked: 2 times
Been thanked: 5 times

Re: CW Dominator tech question....

Post by Eau Rouge »

They are not the same. Jason is right, they are Yokomo hubs. Any Yok wheel will work perfectly, but not an on-road wheel.

User avatar
LTO_Dave
Approved Member
Posts: 1731
Joined: Tue Mar 03, 2009 8:33 am
Location: Rossiter, PA
Has thanked: 47 times
Been thanked: 250 times

Re: CW Dominator tech question....

Post by LTO_Dave »

I actually asked this question on DODC because I wanted to mount the Dominator Cyclone wheels to the pancar adapters on my Slingshot.

Here's the thread: http://www.dirtoval.com/forums/showthread.php?t=37401

I found a pic of a Dom with the BBS pancar wheels mounted, but never received a response.

Image

User avatar
Eau Rouge
Approved Member
Posts: 2224
Joined: Sun Jul 30, 2006 3:59 am
Location: Aurora, Illinois
Has thanked: 2 times
Been thanked: 5 times

Re: CW Dominator tech question....

Post by Eau Rouge »

Someone had to custom make those adapters to use pan wheels on the Dom/Yok axles. I don't know why you would want to, those tires on a Dom would give you an unusable and non-adjustable ride height, and there are plenty of foam tires available for Dominators.

The inside mounting diameter of a Dominator wheel is a LOT smaller than the on road wheel, and the bolt holes are not the same. Those adapters are not the same.

:|

User avatar
Brandon G
Approved Member
Posts: 2106
Joined: Mon Oct 01, 2007 8:23 pm
Location: Nashville, TN
Been thanked: 3 times

Re: CW Dominator tech question....

Post by Brandon G »

I have a few 10L rear wheels, gold aluminum BBS style. I can machine them to whatever width I would need to fit the OE track width and tire width of the Dominator . Seems that the adapters on the Dom uses the yoke measurements, so at this point I will either need to scrap the idea, or just machine adapters to fit the axles to 10L rear wheels.

I guess I will just fire up the lathe and get to work.

After the dominator arrives at my door, that is.

  • Similar Topics
    Replies
    Views
    Last post

Return to “Temple's RC10 Tech Forum”

Who is online

Users browsing this forum: No User AvatarCommonCrawl [Bot] and 8 guests