BME Porsche
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
BME Porsche
So i got a nice brushed chassis in the bst (thanks Paul)
As i havent run any DS for a few months i stated getting some withdralw symptoms And as every build i do i always want to use DS parts it seemed only fair to just go with it on this one
build list parts so far
BME brushed alloy chassis
RPM T bulkhead
HPI 50mm shocks
DS front and rear arms
bolink rear shock tower
Lethal weapon trans
DS rear carriers
Hot Trick front wide nose
DS shiny CVD,s
Pan car F/R wheels and tire,s
1/4 inch alloy box for the braces
bellcranks alloy ballraced of of a graphite rc10
Electronics
novak 13.5 B/L motor
ESC Velineon VXL 3m 1/18
servo traxxas 2056 waterproof
As i havent run any DS for a few months i stated getting some withdralw symptoms And as every build i do i always want to use DS parts it seemed only fair to just go with it on this one
build list parts so far
BME brushed alloy chassis
RPM T bulkhead
HPI 50mm shocks
DS front and rear arms
bolink rear shock tower
Lethal weapon trans
DS rear carriers
Hot Trick front wide nose
DS shiny CVD,s
Pan car F/R wheels and tire,s
1/4 inch alloy box for the braces
bellcranks alloy ballraced of of a graphite rc10
Electronics
novak 13.5 B/L motor
ESC Velineon VXL 3m 1/18
servo traxxas 2056 waterproof
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
Re: BME Porsche
i always like the foam pan car wheels they look mean and seem to grip good depending on the compund so i finally figured a way to mount them on a gear box car i used one of these
it is about a 1/32 to small so i rapped one band of electrical tape around it making sure to not overlap the tape. then cut about 8 grove,s into the tape and slighty into the plastic of the adapter , i then pushed it into hole with a large coin as to seat the adapter flush on the inside of the wheel.
Then a thick squirt of CA glue and let dry for 12hrs
it is about a 1/32 to small so i rapped one band of electrical tape around it making sure to not overlap the tape. then cut about 8 grove,s into the tape and slighty into the plastic of the adapter , i then pushed it into hole with a large coin as to seat the adapter flush on the inside of the wheel.
Then a thick squirt of CA glue and let dry for 12hrs
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
Re: BME Porsche
the front will be the next design challenge i will have to make a custom shock tower .
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
Re: BME Porsche
yes the more i build the less i feel i should run it its such a basic desinge, maybe i will just fold some alloy and make my own .
Its true the material used was thin so i can see why the screws holding on the nose dont hold on the 100 degree sink .
Paul
Its true the material used was thin so i can see why the screws holding on the nose dont hold on the 100 degree sink .
Paul
- rc10johnny
- Approved Member
- Posts: 1304
- Joined: Sun Sep 27, 2009 6:48 pm
- Location: Richmond Va.
- Been thanked: 1 time
Re: BME Porsche
Paul,sweet lookin build...as always... the DO guys have a front shock laydown system that should work for the shocks,cant remember the name but I'm sure someone will know here,it has a center post that the shocks mount to,should work.. JohnnySr
- drbelleville
- Approved Member
- Posts: 815
- Joined: Wed May 20, 2009 5:03 am
- Location: My Adopted state - Texas
- Been thanked: 1 time
- mrhemi1971
- Approved Member
- Posts: 127
- Joined: Sat Sep 04, 2010 1:29 pm
- Location: Hammonton, New Jersey
Re: BME Porsche
Is that a Parma body? I have one thats a slant nose, and I was wondering if they ever did a normal 911. Looking good, I'm jealous!
ASSOCIATED OR NOTHING!!
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
-
- Approved Member
- Posts: 2022
- Joined: Sat Jan 20, 2007 4:41 pm
- Location: Cape Carteret.NC
- Been thanked: 22 times
Re: BME Porsche
I did up my black BME chassis with my DS too.I need a rear tower like that to finish it.
DON
DON
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
Re: BME Porsche
i got three, two with kyosho out drive,s and i sat up till 4am on sta to get my first rc10 vertion and they are all going into runnersLTO_Dave wrote:I like your vision.
Dang, I gotta get me one of those Lethal Weapons.
Paul
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 9 Replies
- 1460 Views
-
Last post by kaiser
-
- 72 Replies
- 6059 Views
-
Last post by marlo
-
- 0 Replies
- 582 Views
-
Last post by Wizemanne
-
- 3 Replies
- 630 Views
-
Last post by mat69
-
- 32 Replies
- 5106 Views
-
Last post by 1968
-
- 0 Replies
- 958 Views
-
Last post by V12
-
- 1 Replies
- 634 Views
-
Last post by shodog
-
- 8 Replies
- 205 Views
-
Last post by mAdMan