Super diff and alloy front gearbox housings

Moderators: scr8p, klavy69

2 posts • Page 1 of 1

kaszal: Approved Member; Posts: 342; Joined: Wed May 12, 2010 11:04 am

Super diff and alloy front gearbox housings

Post by kaszal » Sun Mar 20, 2011 7:40 am

I've seen these parts on a couple cars on various forums... but I would love to know where I can get them (arm and leg ready to sell)

Incredible_Serious: Approved Member; Posts: 3298; Joined: Tue Jan 29, 2008 5:09 am; Location: Melbourne, Victoria, Australia; Has thanked: 1201 times; Been thanked: 735 times

Re: Super diff and alloy front gearbox housings

Post by Incredible_Serious » Sun Mar 20, 2011 11:20 pm

PM coming...

Alex

Osiris is the key.

"The world looks so much better through beer goggles... except Farmer in his underwear" - Ken

Look out for Todd K. - he's a convicted serial killer!!!

2 posts • Page 1 of 1

Similar Topics

Replies

Views

Last post

Procat Front Trans housings T055 differences

by Jools » Sun Jan 18, 2015 1:01 am » in Schumacher Forum

First post

I have two of these housings, both T055, one which has no slot for the tensioner bar and has a bearing housing opening of 15.8mm with 'shoulder' dia of 11.8mm - Fits the flanged bearing 12x8x3.4mm with 13.5mm flange).
The other housing which does...

Last post

Just regarding bearings, take a look at this shot. The bearings setup is very different.
Older type trans housing on the left has a 12mm opening and a 'shoulder' which suits the smaller flanged bearing, whereas the later housing on the right is...

7 Replies

2124 Views

Last post by Jimbo
Sun Jun 21, 2015 9:34 pm
GPM alloy gearbox kit

by DennisM » Fri Apr 20, 2012 7:46 am » in Yokomo Forum

First post

Has anyone ever used this?
I´ve been through a lot of pictures, but haven´t spotted one.

Scorpion parts 007.JPG

Last post

cool, I didn't know they were already around at that time. It looks like the wide type used from 93 back to first dogfighter with belt transmission.

3 Replies

745 Views

Last post by Mr. ED
Fri Apr 20, 2012 2:11 pm
Topcat/Cougar Alloy gearbox case.

by 8rad » Fri Apr 15, 2011 1:56 pm » in Schumacher Forum

First post

Has anyone seen one or have one they can throw up some pics of?

I never knew they existed until today!

Last post

There was a red one of these (from GPM) for sale in the BST ..... but it sold.

P1040181a.JPG

Alex

11 Replies

1333 Views

Last post by Incredible_Serious
Mon May 16, 2011 11:40 pm
Question about JRX2 Gearbox Diff

by a01butal » Fri Feb 20, 2009 2:04 pm » in Losi Forum

First post

When assembling a new diff what are you Losi veteran's doing with the A-3018 small thrust bearing. The problem is you can't or I can't seem to find the Belleville washers in the proper size. Do you still need them on the screw(shaft) for pressure or...

Last post

Anthony helped me out just great.

8 Replies

726 Views

Last post by a01butal
Sat Feb 21, 2009 1:44 pm
RC10 Stealth Gearbox Gear diff

by Nobby Sideways » Tue May 10, 2016 7:21 pm » in RC10 Buggy Forum

First post

Gents,

It turns out that the ham fisted chap that I got my poor old Team car off of had taken all the balls from the diff then glued the cup drives into the drive gear, making one big locked together lump. I've driven my other RC stuff with a...

Last post

They did not make a gear diff for the original stealth. Pretty much that was a time period ball diff standard. and was an upgrade on every rc car ot go to.

The stealth with the b4 slipper set up should be good for an 8.5 brushelss

Exactly ^^^

6 Replies

1227 Views

Last post by jeepy2013
Wed May 11, 2016 6:20 pm
Robinson Racing alloy RC10 DIFF gears

by mk-Zero » Tue Dec 12, 2017 4:47 am » in Conklin Performance Designs

First post

I have two of these in stock. $22 each + shipping. They come supplied with diff balls as shown. These are a direct replacement for the plastic RC10 DIFF gears.

20171210_173158-1008x756.jpg

Last post

Sorry, I only have the diff gears.

4 Replies

1911 Views

Last post by mk-Zero
Wed Dec 26, 2018 1:50 am
Alloy Servo Saver Assembly and Front Bulkheads?

by mikedealer » Sun Jun 24, 2007 7:17 pm » in RC10 Buggy Forum

First post

well after putting all my parts together, ordering what i need, researching similiar B4 parts to put on my classic car, i would like to find a servo saver steering assembly in alloy. I would also like to find a alloy front bulkhead set. Anyone have...

Last post

ya i took the hingepins into account and did a test drill press to make sure i could make them fit and they took pretty well.

good to know GT stuff works with b1 parts etc.

2 Replies

487 Views

Last post by mikedealer
Sun Jun 24, 2007 10:45 pm
MIP ULTIMA SUPER DIFF

by GJW » Sat Dec 29, 2007 10:59 pm » in Vintage Catalogs / Instruction Manuals

First post

GOT ONE OF THESE THOUGHT ID AD IT (HOPE THE PHOTOS ARE OK) 144_4456.JPG

Last post

Thanks for posting this, I have the MIP ball diff and going over the instructions, I noticed some points I wasn't aware of.
The resolution is a bit low though, and in some places its really hard to make the words. In the future you might want to...

1 Replies

956 Views

Last post by Snake Plissken
Wed Jan 02, 2008 8:32 am

Return to “Schumacher Forum”

Who is online

Users browsing this forum: CommonCrawl [Bot] and 0 guests