RC10Talk - The Net's Largest Vintage R/C Community

Congratulations!

Infants sometimes accidentally scratch themselves with their fingernails. A pair of baby socks over the hands takes care of that pretty well.

Unscented baby wipes and A&D gel do a good job preventing and recovering from diaper rash.

I just restored my RC10 Championship Edition (B Stamp) that has not run since the early 90's I swapped out most of the parts with matching aluminum, and still have the original parts (some broken) I did a simple paint job to show off the gold pan. I thought I would share with this community. thumbna...

Thank you all! I really appreciate the practical advice around infant fathering too...your stories and suggestions are so helpful! Lot of trial and error, dividing roles to make the process efficient. Taking a simple shower and eating a quiet meal suddenly became a small luxury haha. In Korea, the g...

That's normal and ok. The nylon in the rear arm mount is very thin where the hinge pin hole and the dogbone clearance cove meet. Some people trim that to fully expose the pin and make it look neater, some leave it just like that. However for part integrity you should rehydrate your nylon parts if it...

I acquired a new build buggy from mikea96 several years ago. I was very pleased with his vision, but the purist in me decided to strip it down and make it an AE parts car only. The pic below shows some of the original parts that were sourced. Neon yellow chassis is an original B stamp. Other parts w...

I just finished the design of a 3D printed rear bulkhead for my RC10T. I printed it using carbon fiber infused ABS. The original bulkhead weighted in at 25g, this printed part weighted in at 9g without the brass threaded inserts, 13 with the inserts. Everything seems to work fine, I suspect that it ...

Looks like you’ve got lots of parts to work with. Nice Yes the black 6 gear only motor plate would be correct for the TQ10. Thanks for confirming! This 6 gear seems to have a bunch of hours on it. I don't have a lot of history with the RC10, but this is the most wear I've seen in my experience. 202...

T3 Sport kit comes with a 7378 3/16" axle.

Team Associated T3 Bearing Kit
https://www.avidrc.com/flexkit/?kit=215&kitname=T3

Hello all, Just a quick post about Rubrix Racing Products, their site/store has been down for a couple of days now. I connected with the owner and learned that he had an issue with the existing website provider and is in the midst of switching things over to a new vendor. New website - www.RUBRIXRC....

Well, I wasn't expecting that!

Here are some relatively rare Yokomo 870c white nylon suspension arms. I'm tempted to replace the black arms with these.
As close to Jesus' legendary cup as there is

Hey all, After a conversation at work after one guy bought a Tamiya Frog, I remembered my old Nikko Black Fox I have up in the loft. Brought it down and loaded it with batteries, but it seems dead as a door nail. Light comes on the remote, and there appears to be volts at various places on the board...

Got the Goldpan rebuild done for my brother’s 40th. Fun project! I always have difficulty uploading pics on this forum (iPhone user…), but I was happy with how it turned out for a basher.

On to rebuilding my old Stadium Blitzer for the 6 yo boy…

All you need is Superglue, Baking Soda, and a dremel. https://i.postimg.cc/d0tbwWcW/E2-BE7-ACF-D47-B-4725-9-ABA-DC71-A525-E286.jpg Stripped. https://i.postimg.cc/9MjF6Qs9/E7420051-4375-4176-B999-802-B419-AC3-E7.jpg Sprinkle on the baking soda dry over the sink. Wipe smooth with your finger tip. http...

I haven’t had to buy anything yet. Let’s see how far I can get. :mrgreen: https://i.postimg.cc/VvNw0zqS/9380-DB4-D-6-BFD-4-A86-A457-A7-D10-F3-AC0-C4.jpg https://i.postimg.cc/76z4gKd4/2-CA3546-B-754-E-44-DB-92-ED-6127-B91-E7-D09.jpg https://i.postimg.cc/h4wx4vb7/338-A590-A-026-F-4-E28-AA03-9460125-F6...