Yokomo MR4-BC and MR4-BC special builds

The place for all things Yokomo.

Moderators: scr8p, klavy69

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Having been a way from any Yokomo builds since my WCS build I thought I'd jump back in with a couple of Yokomo MR4-BC builds.

The first is a standard MR4-BC which I snagged of ebay for okay money, I managed to get a donner MR4-TC for a the special chassis and top brace, one way adaptor and one way front diff and a few other bits. I plan to fit MR4 - bx shocks, MX-4 slipper and LWB kit to this one. I'm still waiting for some parts to arrive so I will update the thread when I start the build.

N.B pictures taken from ebay listing.
Attachments
s-l1600 (1).jpg
s-l1600.jpg
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

The second build is a MR4-BC special which I got from Japan Yahoo auctions for an excellent price, it has the special shocks, special chassis and top brace one way adaptor (no special slipper unfortunately), special wheels and adaptors, the LWB conversion and I think a one way front diff which I will know for sure when I strip her down.

This one doesn't need much work just a really good clean up and some TI turnbuckles which I have already got.
Attachments
DSC_1760.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Just for comparison here is a picture of the difference between the special shock and the later MR4-bx shock. As you can see although similar there are a few differences namely the bore seems smaller on the special and the bottom shock seal part is different. On the later shock the seal consists of three plastic spacers and two o-rings on the special shock there is only one spacer and two o-rings. The caps and the spring retainers are the same.
Attachments
DSC_1762.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

I thought I had managed to find a LWB kit but the shop I had purchased from thought they had it in stock but it transpired that this was not the case so I'm going to modify the parts myself to do the conversion.

Taking measurements from the special I need to modify the rear bulkhead and get the part down to around 24mm.
DSC_1781.JPG
DSC_1782.JPG
Not quite worked out the best way to do this yet.

The second modification is removing part of the rear suspension block, I did this by taking measurements from the special and using a jr hacksaw and a file. For this modification to work you will still need the rear alloy suspension bracket and the spacer to push the rear shock mount outwards, the spacer as it happens is the same spacer as the one used when fitting the anti roll bar kit in a MR4 TC, luckily I have.
DSC_1785.JPG
DSC_1784.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

The parts needed for the conversion.
DSC_1790.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Making slow progress on these builds after I contracted the 'human malware' but I'm on the mend.

First up got all the bits for a MX-4 slipper. Not sure if this is going in the official special or the modified standard car.
DSC_1796.JPG
I managed to modify the rear gearbox parts of the LWB conversion using my trusty Dremel, not as neat as factory but more than functional. As it turns out I needed have bothered as the LWB bulkhead arrived after I was told no stock was available.

First picture shows the modified parts:
DSC_1801.JPG
DSC_1801.JPG (28.58 KiB) Viewed 3964 times
DSC_1801.JPG
DSC_1801.JPG (28.58 KiB) Viewed 3964 times
Second picture shows the factory modified parts.
DSC_1800.JPG
I also modified the chassis to accept the LWD conversion.
DSC_1797.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

I came across a bit of an issue with this one. I had planned on using a chassis from the MR4-TC but is transpires that the chassis will not work if you use the standard MX-4 spur gear as it does not have the necessary molding in the bottom of the chassis (Picture below) which causes clearance issues.
DSC_1811.JPG
The correct chassis is Yokomo ZS-002GB Graphite Main Chassis. I managed to get one in the UK from DMS so I decided to use that one for the restoration of the Special.
DSC_1809 (1).JPG
DSC_1813.JPG
DSC_1814.JPG
DSC_1818.JPG
DSC_1819.JPG
Just a few things to finish and this one will be done.
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Got a little bit done last night on the rear of the MR4-BC, the pictures below show the parts needed for the LWB conversion. I found the right plastic spacers in my parts bin and the rear inner hinger pins are the standard items. You will need to put a hinge pin retaining screw on the front side of the rear arms to stop the hinge pin migrating forwards.

The small spacer are used towards the rear and take up the place of the original molded plastic piece used on the standard car to retain the rear arms which has been removed in the LWB conversion. The blue alloy piece is used to retain the rear hinge pins.

DSC_1825.JPG

How it looks when it is all fitted and complete.

DSC_1832.JPG
DSC_1837.JPG
:shock:

User avatar
Toaster
Approved Member
Posts: 422
Joined: Fri Jul 27, 2007 2:55 am
Location: Toronto, ON
Has thanked: 473 times
Been thanked: 135 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Toaster »

Great work, always wanted to find a way of modifying a ‘BC’ as they always seem to pop up every once in awhile at a decent price (at least right now given how crazy prices are getting).

Will be following with great interest! Keep it up.
I come for the RC10's but stay for the Yokomo's :P

Current projects:
1993 WCS Faux-komo
1994 Yokomo Box-Art
RC10GT Restoration

iiokurud
Regular Member
Posts: 6
Joined: Wed Dec 09, 2020 2:06 pm
Location: York, PA
Has thanked: 8 times
Been thanked: 2 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by iiokurud »

Great post! I have a NIB MR4BC on the way and a used one, not sure my plans yet but following and thanks!

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

I thought I'd update this project.

The second build is going to be a bit of an MX-4, MR4-BC, MR4-TC MR4-BX mix up build. I'm I'm using a front bulkhead cap from the MX4 and the slipper assembly the front and rear shock towers and camber link, a MR4-TC front one way, MR4-BX shocks, JC racing wheels and all new Lunsford Ti turnbuckles. The Chassis and top deck are from the MR4_BC special with the LWB conversion.


DSC_1862.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

A couple of shots of the chassis build.


DSC_1864.JPG
Attachments
DSC_1868.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Front and rear shock towers.
Attachments
DSC_1870.JPG
DSC_1869.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Completed chassis.
Attachments
DSC_1872.JPG
:shock:

User avatar
Alex B
Approved Member
Posts: 429
Joined: Tue Dec 30, 2008 10:23 am
Location: Wales
Has thanked: 22 times
Been thanked: 44 times

Re: Yokomo MR4-BC and MR4-BC special builds

Post by Alex B »

Finished other than the electrics.
Attachments
DSC_1887.jpg
DSC_1884.jpg
DSC_1883.jpg
DSC_1882.jpg
DSC_1881.jpg
DSC_1878.jpg
DSC_1877.jpg
DSC_1876.jpg
:shock:

  • Similar Topics
    Replies
    Views
    Last post

Return to “Yokomo Forum”

Who is online

Users browsing this forum: No User AvatarCommonCrawl [Bot] and 1 guest