Thorp Dirt Burners Losi JRX2 LRM Gears
-
- Super Member
- Posts: 678
- Joined: Sun Oct 06, 2019 11:33 pm
- Location: Ill-Noise, USA
- Has thanked: 953 times
- Been thanked: 564 times
Thorp Dirt Burners Losi JRX2 LRM Gears
You don’t see much info out there about these…This is from my collection for reference.
Thorp hard anodized aluminum gears.
Early parts:
#5101 left gear
#5102 right gear
#5103 Diff gear
Later they came out with a center bearing diff gear, which Losi also did with it’s plastic gears. Unlike Losi that used two special 7/64” wide bearings, Thorp uses two of the standard 1/8” wide bearings. The #5108 right side gear is machined slightly deeper than the #5102 right side gear to accommodate the two bearings.
Center bearing diff parts:
#5101 left gear
#5108 right gear
#5107 Diff gear
Top gear and side gears are made from Delrin. Notice the side gears have been hollowed out/lightened..like the Losi low friction gear set.
More info: https://www.rc10talk.com/viewtopic.php?f=27&t=39934
Thorp hard anodized aluminum gears.
Early parts:
#5101 left gear
#5102 right gear
#5103 Diff gear
Later they came out with a center bearing diff gear, which Losi also did with it’s plastic gears. Unlike Losi that used two special 7/64” wide bearings, Thorp uses two of the standard 1/8” wide bearings. The #5108 right side gear is machined slightly deeper than the #5102 right side gear to accommodate the two bearings.
Center bearing diff parts:
#5101 left gear
#5108 right gear
#5107 Diff gear
Top gear and side gears are made from Delrin. Notice the side gears have been hollowed out/lightened..like the Losi low friction gear set.
More info: https://www.rc10talk.com/viewtopic.php?f=27&t=39934
-Brad
-
- Approved Member
- Posts: 72
- Joined: Sat May 30, 2015 6:43 pm
- Has thanked: 7 times
- Been thanked: 11 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
I have that setup in my original car. I was able to find one side on ebay for building another, but not the other.
- ChocoTaco73
- Approved Member
- Posts: 111
- Joined: Wed Jan 26, 2022 6:53 pm
- Location: Las Vegas, NV
- Has thanked: 57 times
- Been thanked: 98 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
Cool stuff but never understood the need, unless someone was running insane power on a high-bite track. Even though there weren't any way back when.
James - Losi fanatic
-
- Super Member
- Posts: 678
- Joined: Sun Oct 06, 2019 11:33 pm
- Location: Ill-Noise, USA
- Has thanked: 953 times
- Been thanked: 564 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
I think the melted diffs were just a result of poor maintenance and lack of keeping up on the adjustment. Yeah, these immediately defeat the Low Rotating Mass notion but are also very cool because of how nicely machined and smooth they are!ChocoTaco73 wrote: ↑Fri Aug 26, 2022 8:35 pm Cool stuff but never understood the need, unless someone was running insane power on a high-bite track. Even though there weren't any way back when.
-Brad
-
- Super Member
- Posts: 678
- Joined: Sun Oct 06, 2019 11:33 pm
- Location: Ill-Noise, USA
- Has thanked: 953 times
- Been thanked: 564 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
The Thorp Delrin top shaft gear also fits properly on the Losi A-3120 Hydra-Drive/Slipper shaft. Which means it will also fit the A-3007 JRX-Pro top shaft and the A&L Power Clutch shaft.
-Brad
-
- Approved Member
- Posts: 711
- Joined: Sun Apr 15, 2012 11:20 pm
- Location: Bellingham, Wa
- Has thanked: 14 times
- Been thanked: 57 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
I was one of those dummies who thought the diff in the Jrx2 was a slipper and melted the stock gears. I ran this Thorp set which allowed me to continue my dummy ways! As a young teen, I didn’t know any better.
ChocoTaco73 wrote: ↑Fri Aug 26, 2022 8:35 pm Cool stuff but never understood the need, unless someone was running insane power on a high-bite track. Even though there weren't any way back when.
-
- Super Member
- Posts: 678
- Joined: Sun Oct 06, 2019 11:33 pm
- Location: Ill-Noise, USA
- Has thanked: 953 times
- Been thanked: 564 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
Thorp gearbox with Losi slipper completed and installed.
-Brad
- RogueIV
- Super Member
- Posts: 552
- Joined: Sat Aug 27, 2022 10:04 pm
- Location: W. Mass
- Has thanked: 1159 times
- Been thanked: 469 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
These aren't immune being neglected or treated as a slipper. This is out of my old LXT. Not sure how long this was abused for but it's got a pretty deep groove in it.
Consistency is the key I keep misplacing.
-
- Approved Member
- Posts: 537
- Joined: Sat Jun 24, 2006 6:41 am
- Location: Herrenberg, Germany
- Has thanked: 29 times
- Been thanked: 66 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
Those aluminum gears are nice.
What got me into higher grade RC buggies was when my younger brother bought a used Losi Jrx Pro SE. I then bought a used RC10T i think. That was the time when the Losi XX and the RC10 B2 and T2 had already been released.
Then when old RC stuff was still dirt cheap on eBay, early 2000s I guess, I also bought a JRX T (maybe a junior T) to accompany the buggy.
I don't know if I was tightening the diff too much, but I managed to crack two diff (LRM) rings, and was fed up and sold the Truck again.
If I remember correctly the hexes on my diff gears were just slightly too large for the hex holes in the diff rings.
Anyway that was my experience with the LRM Diff. I found the xx / Pro SE transmission to be way superior.
What got me into higher grade RC buggies was when my younger brother bought a used Losi Jrx Pro SE. I then bought a used RC10T i think. That was the time when the Losi XX and the RC10 B2 and T2 had already been released.
Then when old RC stuff was still dirt cheap on eBay, early 2000s I guess, I also bought a JRX T (maybe a junior T) to accompany the buggy.
I don't know if I was tightening the diff too much, but I managed to crack two diff (LRM) rings, and was fed up and sold the Truck again.
If I remember correctly the hexes on my diff gears were just slightly too large for the hex holes in the diff rings.
Anyway that was my experience with the LRM Diff. I found the xx / Pro SE transmission to be way superior.
*** POWDER - KING ***
-
- Approved Member
- Posts: 1998
- Joined: Fri Feb 16, 2007 10:09 pm
- Location: Upstate NY
- Been thanked: 12 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
I've gotta find that 5108 to fill in my collection.
Does anyone know what 5109 or 5111 are? (assuming they weren't skipped)
The 5110 complete set has a ball bearing center gear and the deeper recess side gear as well, didn't know it was available separately though.
5100 Diff gear set
5101 left gear
5102 right gear
5103 Diff gear
5104 Top gear (delrin)
5105 Top Shaft
5106 Gear and Shaft Set
5107 Diff gear (bearing style(
5108 right gear (for Bearing style center gear)
5109 ??
5110 Transmission set 5 piece (ball bearing center gear)
5111 ??
5112 Out Drive Gears
Does anyone know what 5109 or 5111 are? (assuming they weren't skipped)
The 5110 complete set has a ball bearing center gear and the deeper recess side gear as well, didn't know it was available separately though.
5100 Diff gear set
5101 left gear
5102 right gear
5103 Diff gear
5104 Top gear (delrin)
5105 Top Shaft
5106 Gear and Shaft Set
5107 Diff gear (bearing style(
5108 right gear (for Bearing style center gear)
5109 ??
5110 Transmission set 5 piece (ball bearing center gear)
5111 ??
5112 Out Drive Gears
-
- Approved Member
- Posts: 1998
- Joined: Fri Feb 16, 2007 10:09 pm
- Location: Upstate NY
- Been thanked: 12 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
A thorp diff gear vs brass top gear, nice and pointy at the tooth tips. There was a ton of brass dust in the gearbox when I received it, probably could have run a couple more packs before it fully let go.
Still fared better than some of the plastic gears have
-
- Super Member
- Posts: 678
- Joined: Sun Oct 06, 2019 11:33 pm
- Location: Ill-Noise, USA
- Has thanked: 953 times
- Been thanked: 564 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
Nice collection @aconsola! I have never seen the sets..thanks for posting that pic. I’m not sure what those missing numbers are either. I will guess they are another combination of parts..like maybe all the Delrin gears in a set.
-Brad
- ChocoTaco73
- Approved Member
- Posts: 111
- Joined: Wed Jan 26, 2022 6:53 pm
- Location: Las Vegas, NV
- Has thanked: 57 times
- Been thanked: 98 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
Funny, I picked up a JRX buggy for parts and was pleasantly surprised to see Thorp gears and MIP diff rings. I went ahead and picked up a non-slipper topshaft and output gears for my shelf queen.
James - Losi fanatic
- Nige55
- Approved Member
- Posts: 63
- Joined: Thu Apr 24, 2008 3:30 pm
- Has thanked: 7 times
- Been thanked: 14 times
Re: Thorp Dirt Burners Losi JRX2 LRM Gears
BattleTrak wrote: ↑Sun Aug 28, 2022 9:18 pm The Thorp Delrin top shaft gear also fits properly on the Losi A-3120 Hydra-Drive/Slipper shaft. Which means it will also fit the A-3007 JRX-Pro top shaft and the A&L Power Clutch shaft.
I've just done this exactly after I received the topshaft and delrin gear today. However it binds when I tighten the gearbox fully. Did you need to grind any gearbox inner? I notice my Thorp gear is marginally wider than the stock gear for that topshaft.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 326 Views
-
Last post by Synergy
-
- 2 Replies
- 1220 Views
-
Last post by vwjuice
-
- 8 Replies
- 1519 Views
-
Last post by Nige55
-
- 5 Replies
- 664 Views
-
Last post by Coelacanth
-
- 11 Replies
- 1772 Views
-
Last post by slow_jun
-
- 5 Replies
- 1008 Views
-
Last post by civilguy
-
- 5 Replies
- 886 Views
-
Last post by R Cane
-
- 4 Replies
- 1006 Views
-
Last post by JK Racing
Who is online
Users browsing this forum: No registered users and 10 guests