What's on the table? Current Projects.....

[mrlexan]

OK, I know that my effort will be pointless , but I posted this in the hopes to get a couple people off my back and also just to start a thread about what current projects are. Jason/David/Anthony, note the top right corner!!!!!!! GET OFF ME! Current focus is getting my 1st Gen Losi stuff completed. One Proformance, one Pro/Proformance hybrid, and my full tilt X2. I think I have hit a road block on the X2. I know what I want to complete it, just finding them will be the problem....... Robinson rear arms.

Let's see what you all have these days in progress or soon to be completed.

[scr8p]

what? top right corner? that one doesn't count.

you need to build an RC10 without a t, gt, t2, t3, t4, b2, b3, b4, l, lss, lso, l2, l3, l4, tc3, tc4, tc5, or any other variation behind it.

RC10 followed by c.e., team car, or worlds is fine though.

[mrlexan]

Oh, now you are getting specific.

[scr8p]

Oh, now you are getting specific.

of course.

i'd take pics of my workbench, but they all look like bombs were dropped on them.

do you want those white robinson arms?

[MelvinsArmy]

Absolutely nothing!!!

I'm moving next weekend, so everything I own is packed up.

But, when I am all moved in, it's time to build some Vintage Natsmobiles. I'm planning a gold tub buggy and some kind of stadium truck.

[aconsola]

I'll be working on rc's quite a bit as the basement is nice and cool. We haven't installed central A/C yet as we were waiting for our other house to sell.
This one I just got together last night. I am waiting for RPM rear arms and those will replace the andy's that are place holders for now. The front was pre-hacked by the previous owner and is done well, but there are a lot of holes that are luckily covered by the bumper and bulkhead. I've got to figure out how to fit a body on there, any ideas?

whatsonthetable 005.jpg (93.29 KiB) Viewed 2212 times

whatsonthetable 005.jpg (93.29 KiB) Viewed 2212 times

Next up is an RPM 10-T conversion. I've got to tear down and re-dye. What I think was originally black has faded to a deep chocolate brown, only problem there is I don't have anything big enough for the chassis tub. next to that is a jrx-pro waiting for re-assembly.

whatsonthetable 004.jpg (62 KiB) Viewed 2213 times

whatsonthetable 004.jpg (62 KiB) Viewed 2213 times

once that is done I have some electronics that mostly all have homes they need to be put into, I've been a bit lazy with the wiring on the last few builds, skipping to the next project without actually finishing anything.

whatsonthetable 006.jpg (100.29 KiB) Viewed 2208 times

whatsonthetable 006.jpg (100.29 KiB) Viewed 2208 times

I guess we should lay off Jay now that he is building some good stuff, although some action shots of the finished products would be better. . .

[badhoopty]

I've got to figure out how to fit a body on there, any ideas?

i always just trim a lil landing strip that fits between the tower hole.

[MelvinsArmy]

i always just trim a lil landing strip that fits between the tower hole.

[Asso_man!]

Hey Jay, nice workbench you have there, but it seems I can't find any RC10 on there, must be a long time since you saw your last one



Anyway, it's not because your car has gold shocks that it is called a '10

[mrlexan]

Hey that's not fair David.

Looking good Anthony.

[Asso_man!]

Sorry Jay, just picking on you for the last time it seems.

[CM_113]

i always just trim a lil landing strip that fits between the tower hole.

don't do that i dang near choked on my diet sun drop,

[JPAE07]

Here are my latest projects.
First, I found this JRXT buried on a shelf at a local hobby shop for $20. I had one of these bitd which i built but never ran, probably due to the leaky shocks. It ended up just sitting until I sold it a few years later.

LosiJRXT_01.jpg (54.19 KiB) Viewed 2099 times

LosiJRXT_01.jpg (54.19 KiB) Viewed 2099 times

LOSIJRXT_02.jpg (32.87 KiB) Viewed 2111 times

LOSIJRXT_02.jpg (32.87 KiB) Viewed 2111 times

LOSIJRXT_03.jpg (48.04 KiB) Viewed 2098 times

LOSIJRXT_03.jpg (48.04 KiB) Viewed 2098 times

The day after I picked it up, I found another lhs with all the parts I needed to restore it.

LOSIJRXT_04.jpg (69.67 KiB) Viewed 2100 times

LOSIJRXT_04.jpg (69.67 KiB) Viewed 2100 times

Losi's sure seem alot quicker to tear down than RC10s. Also easier to clean too.
Only problem, was I estimated use was minimal based on chassis wear and the overall condition. Once I opened the gearbox I noticed that the diff lube used by the prev owner was actually a thick sticky red grease. The grease must have chemically reacted mixed with heat and fused the diff balls into the diff gear.

JRXTDiffGear_0163.jpg (30.11 KiB) Viewed 2097 times

JRXTDiffGear_0163.jpg (30.11 KiB) Viewed 2097 times

The other gears are shot too. It was the one part I failed to think about replacing. Go figure.


I also have my Runner project, which I am trying to convince myself it was one of Kinwalds cars, due to how the nose plate has been shaped....

Runner1_0152.jpg (36.79 KiB) Viewed 2095 times

Runner1_0152.jpg (36.79 KiB) Viewed 2095 times

Runner2_0155.jpg (20.52 KiB) Viewed 2093 times

Runner2_0155.jpg (20.52 KiB) Viewed 2093 times

Anyways, I plan on reshaping (Seibenelch style) the tub once I find a belt sander, adding a stealth w/B4 topshaft, B4 FT threaded shocks, new carbon WC repro shock towers front and rear, B2 MIP CVDs, B2 wheels, Spectrum DX2.0 or 3.0 controller, LRP Pro Reverse Quantum 7T Speed Control, plus one beater Reedy modified MR.L or MR. Y(reconditioned w/ new springs and brushes)

[markt311]

That diff gear doesn't look like a chemical reaction. That's what those losi diffs were famous for doing if you had them set too loose. I have a collection of lrm gears from the days before the slipper clutch landing strip! I thought we were talking about something else for a minute

[Eau Rouge]

Oooohhhh, a ceramic arm Race Prep modified motor! NICE!