Tamiya Sand Scorcher - 2010 Reissue

The place for all things re-release Tamiya.

Moderators: scr8p, klavy69

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

Image

Finally have the proper mask to stay in the fumes, and paint more seriously. Too windy to paint anything today though.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

Got three coats of primer on
Image

Image

Image

I need to fix some spots, now that I can see them better.

What is the final grit you guys sand your primer to, before paint?

User avatar
XLR8
Approved Member
Posts: 2980
Joined: Sun Feb 19, 2017 8:46 am
Location: north/central Alabama
Has thanked: 1214 times
Been thanked: 878 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by XLR8 »

Honestly, I don't recall sanding the primer.
Maybe if I found sand scratches projecting through the primer or some rough spots, I might have used 1000 grit or finer but only on those spots.
Since I typically use lacquer based paints (i.e. Tamiya TS or Duplicolor) which, I think, melt into the primer (also lacquer based) during those initial final coats, I don't think sanding the primer is absolutely necessary. Well, at least I haven't had a problem doing it that way so far.
Doug

mikea96
Super Member
Posts: 3302
Joined: Thu Oct 01, 2009 8:34 pm
Location: Puyallup, WA
Has thanked: 184 times
Been thanked: 593 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by mikea96 »

I think when I did my scorcher body I did wet sand the primer with 1500 before spraying color on it.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

Really appreciate your input, guys, thanks! I'll go over the bad spots in 1000 grit with water, and then finish up with 1500 or above, wet. Wasn't sure if I could do that, this is the first time I've painted with primer.
Image

Image

Image

Thanks again!


Thinking about getting the center gear diff kit for this, it's weird to try and turn the chassis by the front bumper and have the tires lock up and squeal as they skid around in to place, all new experience for me, have always had the diff in the center. I'll give this a drive without the diff for the first run, and then decide.

mikea96
Super Member
Posts: 3302
Joined: Thu Oct 01, 2009 8:34 pm
Location: Puyallup, WA
Has thanked: 184 times
Been thanked: 593 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by mikea96 »

If you plan running it in dirt and grass the diff is nice but in the sand the stock gear works best.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

mikea96 wrote: Thu May 02, 2024 4:00 am If you plan running it in dirt and grass the diff is nice but in the sand the stock gear works best.
Good to know, thanks! Can't imagine putting this in sand after all the work, grass would be about the most this will see, just want to keep this as clean as can be, it's the one I never thought I could have.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

One more putty, primer, and wet sanding round has got the nose line nearly gone. One more round to go.
Image

Image

Getting the mold lines above the fenders flat.
Image

Camera flash lit
Image

Burned through the primer on the driver's fender mold-line.
Image

Used an entire can of primer, have another ordered and on the way. Hoping to get the TS-26 Pure White over this by next Wednesday.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

Ordered the primer for this project on May 3rd - along with some other Tamiya colors from Amain, them being in Chico CA, and me being less than three hours away from there. Turns out their paint was shipped from Omaha NE, and is still listed as delayed in transit, it was supposed to be here today.

The ground-shipping-only for aerosol cans really slows things down. Need to find a well stocked local spot instead.

Found this video of boxart Sand Scorcher's and a Ranger being bashed on a beach, and while the music should be turned down as low as it can go, or muted, I enjoyed the recklessness.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

Got the bad spots fixed, and the last coat of primer on.
Image

Image

Image

Image

Image

TS-26 Pure White will be going on as soon as the wind lets up, this coming week.

User avatar
XLR8
Approved Member
Posts: 2980
Joined: Sun Feb 19, 2017 8:46 am
Location: north/central Alabama
Has thanked: 1214 times
Been thanked: 878 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by XLR8 »

Beautiful prep work!

Can't wait to see it with some color.

Oh man, this is gonna be good. :D
Doug

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

XLR8 wrote: Mon May 20, 2024 2:31 am Beautiful prep work!

Can't wait to see it with some color.

Oh man, this is gonna be good. :D
Thanks so much! Really hoping to get it right the first time with this paint. I've spent so much time trying to recover from my mistakes - with every last project, I just need to get through these struggling stages, and remember how to do it correctly, once I've finally learned how.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

Image

Image

Image

Image

Image

Image

No drips, a few nits, and limited orange peel. I can live with it.

The wind here makes painting more difficult than it should be. Need to make some changes back there, in order to get better results in the future.

Will put the TS-10 French Blue over this when I can get the weather handled. It could all go wrong, fast - with the next masking, and layer of paint. Going to give it plenty of drying time, may wait two days.

Most difficult model I've ever tried, appreciating the challenge though.

User avatar
GreenBar0n
Super Member
Posts: 725
Joined: Sun Nov 05, 2023 11:08 pm
Has thanked: 559 times
Been thanked: 253 times

Re: Tamiya Sand Scorcher - 2010 Reissue

Post by GreenBar0n »

The paint looks to have settled, or become a bit smoother today, now that it's dry.
Image

The weather is nearly ideal right now to paint the blue layer, but I need to make sure to let the white dry properly.

Really happy with what I have so far now, but I know the masking and the blue layer could change things for the worse in a blink, if I'm not constantly aware of the prep and weather conditions. Will mask it tomorrow, and hopefully paint too if the weather permits.

  • Similar Topics
    Replies
    Views
    Last post
  • sand scorcher reissue got a minor bug - built pics update
    by 59burst » » in Tamiya Forum
    12 Replies
    1867 Views
    Last post by shodog
  • Sand Scorcher 2010
    by Rizzo » » in Tamiya Forum
    11 Replies
    1294 Views
    Last post by Nouseforaname
  • The wait is over! (SAND SCORCHER 2010)
    by Diggley » » in Tamiya Forum
    16 Replies
    2424 Views
    Last post by Diggley
  • Sand Scorcher 2010 OIN
    by ra272 » » in Tamiya Forum
    29 Replies
    5988 Views
    Last post by bearrickster
  • Track runner Sand Scorcher 2010
    by aakoskin » » in Tamiya Forum
    1 Replies
    328 Views
    Last post by Dadio
  • Tamiya 1:1 Sand Scorcher
    by drbelleville » » in Tamiya Forum
    17 Replies
    1738 Views
    Last post by civilguy
  • Tamiya Sand scorcher ball diff
    by rctenracer » » in Tamiya Forum
    2 Replies
    1097 Views
    Last post by Dadio
  • Tamiya Sand Scorcher with Monster Beetle-body
    by Tobbe70 » » in Tamiya Forum
    17 Replies
    2574 Views
    Last post by Tobbe70

Return to “Tamiya Re-Release Forum”

Who is online

Users browsing this forum: No User AvatarCommonCrawl [Bot] and 0 guests