pick my next build for me lol

[discgolfer72]

i have one space left on my car shelf

i have bags and bags of rc10 parts (no white parts left ,excpt rear and front bulkheads)


what should i build

i have 3 pans left ,and 2 trans . a stealth and a 6 gear




out of the three chassis im only intrested in 2 the 3rd is stilla wip

first i have a a stamp original black chassis with stealth and 6 gear holes i refinished it in stuff used to reinforce old car frames (tougher than bed liner and not as heavy texture)



then i have a runner quality gold pan a stamp with only 6 gear holes




im a blank slate right now excpt this will be a runner not a shelf queen
and im def going to use the 3/16 axles and andys/rpm front and rear a-arms

[marlo]

That pan on the right looks like it was sand blasted.

[discgolfer72]

yup need to get some more medium for my blaster to finish it up
it was a old mid engine conversion i had done years ago the tranny shot craps so it got tore down and parts thrown in my parts bin

[marlo]

Careful blasting, I did one years ago and warped it. I flipped it over and lightly blasted the other side to true it up again. And the pressure was low.

[teman]

I vote for a stealth car, black chassis with wide front arms or RPM arms all around

[8rad]

I think you should build a Kyosho.

[discgolfer72]

been there done that koysho bla
lol i have a old koysho indy car that i built and never installed elect on

i was leaning tward the black chassis with the stealth but after a trip to the lhs today im still unable to end up with a complete slipper


i have the inner slipper part but thats it
i picked up a outer slipper today and some rings before that but they dont work to well with the original inner part

(found a older hobby store about 30 min from me so im gonna try there tom for more old stock parts)

any ideas
on the slipper

[scr8p]

either look for the "correct" outer hub and clutch disc on ebay (since it's all discontiued), buy available slipper parts from a b2/b3/t3, or change the entire topshaft and use all b4 stuff.

[discgolfer72]

well im guessing the outer hub i bought at the lhs is a b4(rings are probably b4 as well)
and they had a b4 top shaft as well
is it a drop in replacement or do i need other parts to make it work with the old stealth trans

[scr8p]

I don't think there's an "outer" hub with the b4 slipper. They're both the same. Whats the part number on it?

[discgolfer72]

#9604 was the hub i bought


nip tranny parts i have on hand
#6587 torque control spring
#7664 X2 (think these are the gt diff gears)
#7667 diff out drive (have left to )
#6614 idle gears(i know what they are for lol )
#6610 idle gear pivot (same as above lol)
#7666 drive rings
#6580
#25043

[THEYTOOKMYTHUMB]

That half blasted chassis looks pretty cool. You could do some cool things with that effect if you think it through properly.

[scr8p]

#9604 was the hub i bought

well you'd need another one of those, the slipper pads, spur, spring, nut, and topshaft.

all this plus the b4 topshaft.

http://www.ebay.com/itm/Team-Associated-RC10-B4-1-Buggy-Spur-Gear-Slipper-Clutch-/130875186753?pt=US_Radio_Control_Control_Line&hash=item1e78c4de41

[discgolfer72]

oh yea think its time i dusted this baby off and use it for this build




been trying to find a use for this old thing to maybe now is the time since om using the oval motor

[discgolfer72]

still can figure out how to make an edit of my post



thanks i just bought that kit you linked to ill pick up the top shaft at my lhs in the am


dug thrue my parts and pulled almost a full set of white parts
looks like i missing i front axle carrier and bolth rears
im going to use rpm arms so im good there