MIP Help...

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

toybaron
Approved Member
Posts: 82
Joined: Sun Jan 13, 2008 1:16 pm
Location: NJ, USA
Been thanked: 4 times

MIP Help...

Post by toybaron »

Plenty going on recently with MIP 4X builds...so I dug through my parts boxes and also made a recent trade to try to come up with all parts required for 3 different 4x builds ...

here is the list of what I have, as well as a picture below that does not have the part numbers:

4-10 kit parts (all "100" numbers):

100 belt x3
102a stub axle w pin x2
102b dog bone x2
104 hardware
105 mipet
106 rollers
107 1 way housing
108 outdrives
109 rr drive gear/shaft
113 25 degree spindles
119 19t drive pinion

121 slipper hardware
122 slipper hub
123 slipper mippet

--------------------

RC10 4wd kit parts: (all SP numbers)
23 guide cover
24 cases
25 pinion drive
30 outdrives
31 drive axle
32 coupling drives
33 coupling block and shaft
35 spindles
34 carriers
36 diff kit
45 belt drive
50 steel gears incl sp20, sp8

I got these groups of parts from different buys/trades...they each seem to have different part numbers on parts that look to serve the same purpose between the kits. I have seen that there are at least three different MIP 4x kits for the RC-10 so I could use some help determining exactly what I have, exactly what I need and would certainly be interested in a breakdown of the differences between kits, the timeline, and the improvements...

with regards to parts that I am missing, I am a buyer or trader for these as well....

MIP developments are so much a part of improving the RC-10, they almost warrant their own section on the board... I'd love to see a technical reference section...

Thanks in advance...

toybaron
Approved Member
Posts: 82
Joined: Sun Jan 13, 2008 1:16 pm
Location: NJ, USA
Been thanked: 4 times

MIP Cable Parts picture

Post by toybaron »

No clue on part numbers or what else is needed for this one....

Image

User avatar
shodog
Approved Member
Posts: 3817
Joined: Thu Oct 05, 2006 7:09 pm
Location: Washington
Has thanked: 3 times
Been thanked: 85 times

Re: MIP Help...

Post by shodog »

the first one you describe is the cable version http://www.tamiyaclub.com/showroom_model.asp?cid=5696&id=34 and the second is the generation 2 chain drive http://www.tamiyaclub.com/showroom_model.asp?cid=23780&sid=34

User avatar
Erich Reichert
Approved Member
Posts: 1224
Joined: Wed Jul 25, 2007 7:57 pm
Location: Southbury, CT
Been thanked: 1 time

Re: MIP Help...

Post by Erich Reichert »

hey baron, If you're looking to unload any of that stuff i know joeyskates was looking for sp-45 belt drive.

User avatar
scr8p
Administrator
Posts: 16467
Joined: Wed Feb 08, 2006 2:46 am
Location: Northampton, PA
Has thanked: 27 times
Been thanked: 907 times

Re: MIP Help...

Post by scr8p »

Erich Reichert wrote:hey baron, If you're looking to unload any of that stuff i know joeyskates was looking for sp-45 belt drive.
joey's been looking for an sp-45 for as long as i can remember. :lol:

User avatar
Erich Reichert
Approved Member
Posts: 1224
Joined: Wed Jul 25, 2007 7:57 pm
Location: Southbury, CT
Been thanked: 1 time

Re: MIP Help...

Post by Erich Reichert »

well i mention it bc I sold him one that was lost in the mail and I feel bad so I thought i'd try to help him out.

RETRO R/C
Approved Member
Posts: 954
Joined: Tue Jan 09, 2007 3:10 am
Location: Australia
Has thanked: 7 times

Re: MIP Help...

Post by RETRO R/C »

Those bits look familiar Ron - so does that bench!! ;)

All you need is the front gearcase moulding and front uprights, front alloy blocks (if you are fitting to the RC10) and you are there for the cable kit - as you already have the rear gearbox. You will also need the bearings of course!

I have spare belts for Jase if he needs them. Also still have a number of parts for the belt and cable kits.

Cheers

Darryn
Image
TO KNOW WHERE YOU ARE GOING - YOU HAVE TO KNOW WHERE YOU HAVE BEEN
VENOM International | Factory Pilot - Team SCHUMACHER UK | J-Concepts USA | B-Fast Performance USA | Bugle Boy Racing | MAX Racing Products International

toybaron
Approved Member
Posts: 82
Joined: Sun Jan 13, 2008 1:16 pm
Location: NJ, USA
Been thanked: 4 times

Re: MIP Help...

Post by toybaron »

Darryn, is the correct rear gearbox the early SP-1???

Ron

User avatar
asashaw
Approved Member
Posts: 321
Joined: Thu Apr 05, 2007 5:27 am
Location: NY

Re: MIP Help...

Post by asashaw »

its the one you sent me half of for the cable kit. sp-1 was for the chain drive

User avatar
asashaw
Approved Member
Posts: 321
Joined: Thu Apr 05, 2007 5:27 am
Location: NY

Re: MIP Help...

Post by asashaw »

i have lots of parts to trade also toybaron

User avatar
asashaw
Approved Member
Posts: 321
Joined: Thu Apr 05, 2007 5:27 am
Location: NY

Re: MIP Help...

Post by asashaw »

scr8p wrote:
Erich Reichert wrote:hey baron, If you're looking to unload any of that stuff i know joeyskates was looking for sp-45 belt drive.
joey's been looking for an sp-45 for as long as i can remember. :lol:
I offered him one NIB (sealed bag) for $150. I don't think that is a lot (neither did shodog if I remember correct), but Joey said no. I would not sell my NIB one anymore. But I do have the belt and pulleys from aconsola's car...

RETRO R/C
Approved Member
Posts: 954
Joined: Tue Jan 09, 2007 3:10 am
Location: Australia
Has thanked: 7 times

Re: MIP Help...

Post by RETRO R/C »

toybaron wrote:Darryn, is the correct rear gearbox the early SP-1???

Ron
Yep - your black one mate.......that you beat me to by a day!! .......LUCKY BUGGER !

Cheers

Darryn
Image
TO KNOW WHERE YOU ARE GOING - YOU HAVE TO KNOW WHERE YOU HAVE BEEN
VENOM International | Factory Pilot - Team SCHUMACHER UK | J-Concepts USA | B-Fast Performance USA | Bugle Boy Racing | MAX Racing Products International

User avatar
Dr. Robotnik
Approved Member
Posts: 1442
Joined: Wed Oct 11, 2006 3:05 pm
Location: Nutterham, United Kingdom
Been thanked: 2 times

Re: MIP Help...

Post by Dr. Robotnik »

RETRO R/C wrote: ALL you need is the front gearcase moulding and front uprights, front alloy blocks (if you are fitting to the RC10) and you are there for the cable kit - as you already have the rear gearbox. You will also need the bearings of course!
Bit of an understatement there hahaha.

RETRO R/C
Approved Member
Posts: 954
Joined: Tue Jan 09, 2007 3:10 am
Location: Australia
Has thanked: 7 times

Re: MIP Help...

Post by RETRO R/C »

I have the alloy blocks (just found).

I recently got a set of front uprights in trade - so they are out there.

The toughest bit will be the front gearbox - but ask and you shall find.

Darryn
Image
TO KNOW WHERE YOU ARE GOING - YOU HAVE TO KNOW WHERE YOU HAVE BEEN
VENOM International | Factory Pilot - Team SCHUMACHER UK | J-Concepts USA | B-Fast Performance USA | Bugle Boy Racing | MAX Racing Products International

toybaron
Approved Member
Posts: 82
Joined: Sun Jan 13, 2008 1:16 pm
Location: NJ, USA
Been thanked: 4 times

Re: MIP Help...

Post by toybaron »

Darryn, of course if the alloy blocks are not needed by you, they ARE needed by me...and now to try your magic method----asking---

Hey, anyone have the front gearbox complete??????? cash or trade!!

Thanks!

  • Similar Topics
    Replies
    Views
    Last post
  • Mip Shiny bones vs regular Mip cvd bone
    by JosephS » » in R/C Off-Topic / Chit-Chat
    3 Replies
    601 Views
    Last post by juicedcoupe
  • MIP SP1 with MIP CVDs - Issue with Dogbone Popping out
    by Mwp1111 » » in Temple's RC10 Tech Forum
    11 Replies
    1645 Views
    Last post by jcwrks
  • MIP 1/4 to 3/16
    by rc10johnny » » in Off-Topic / Chit-Chat
    5 Replies
    420 Views
    Last post by rc10johnny
  • MIP ID help please
    by RC10Eh » » in Temple's RC10 Tech Forum
    7 Replies
    702 Views
    Last post by aeiou
  • MIP 4X
    by scootmike » » in Tamiya Forum
    2 Replies
    1023 Views
    Last post by scootmike
  • Mip Gearbox
    by ThomasH » » in Temple's RC10 Tech Forum
    2 Replies
    577 Views
    Last post by ThomasH
  • MIP 4WD ID help
    by vintage racer » » in RC10 Buggy Forum
    5 Replies
    812 Views
    Last post by Mad Racer
  • MIP 4-10 Build
    by EvilAsh » » in RC10 Buggy Forum
    19 Replies
    2135 Views
    Last post by THEYTOOKMYTHUMB

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No User AvatarCommonCrawl [Bot] and 1 guest