p.s. Run b3 wheels if you have access to them. Only reason I'm not is because I'm gonna start racing again when funds permit and will be sharing wheels/tires with my rc10,b4 and b44(rears) to save on how many sets I'll have to have.
Peace and professionlism.....Kabunga signing off!!!
Here is a link that should get you started. http://www.rc10talk.com/viewtopic.php?f=35&t=20904 (hpi 5 spoke rims)
There are a couple other threads about using modern wheels that have some good info. Someone even tried the SC10 hex conversion.
Mark
If you wish to run b4 rear hubs with b4 CVD/CVA's you need to clearance out the inboard bearing approximately 1/8" otherwise the hub will bind because the b4 (B44) shaft is too long. Also, use a countersink afterwards since the curvature of the joint will want to go deeper into the hub that now has a deeper inboard bearing location.
thx for the effort guys. i never knew about those spacers! I think i'm gonna find a wide hex and run hex b4 wheels. I have a hard time with pics on this sight od i'd post pics!
xxx,lunchbox,blackfoot,t4,2 rc10ce's,rc10 graphite,rc10 worlds car,2 rc10 t's,xx4---GONE:mip4wdrc10,rpm worlds,houge rc10,super clod,sand scorcher,f103,frog,xxxt,b2,b3,tc3,jrx2,fox,yr4-m2 usa,yz-10 many more LOL
i'm kind thinking that in order to run this thing and have it feel&look "RIGHT" it might just need some b3 wheels/susp put back on..
i have only run a few laps similar to my b4. but those few laps were so cool that i'd like to string them together. gold tub car needs some love to get consistent tho
xxx,lunchbox,blackfoot,t4,2 rc10ce's,rc10 graphite,rc10 worlds car,2 rc10 t's,xx4---GONE:mip4wdrc10,rpm worlds,houge rc10,super clod,sand scorcher,f103,frog,xxxt,b2,b3,tc3,jrx2,fox,yr4-m2 usa,yz-10 many more LOL
JC Racing are now offering their rear 2.2 YZ10/870C wheels as a pair, so if your looking for a set for your RC10 you no longer need to buy unwanted fronts to get the rears 👍
I have been lurking on here reading up on how to get my CE gold tub (I wanna say 6011 because of the bushings) driving again. It is in pristine condition considering that the only reason it was not run when I was young is because my brother botched...
Last post
Got some pictures of the wheels an how they fit using the drilled out SC10 hex adapters and the mini e-revo wheels
Guys, I have an RC10B2 that I bought right when they came out. It came with 2.15 rear wheels (which are still on it). The Associated PN in my book is 9490, I recently picked up a new set of 9490 wheels and they are a little larger (2.2 ), like my...
Last post
Same wheel in 2.2, same pin and I.D. as well- works fine
Since Tower is not able to supply B2/B3 rear wheels any more (discontinuted) is there an alternative we can use for racing? I had a look at the Thunder Tiger Phoenix BX wheels because TTR stated that this buggy is based on the AE B3 but it...
Last post
I tried fit the rims on the CVDs i have, and they appear a tad small. I think a simple pass of the 3/16 drillbit should take care of it.
MOmo
Had to do the same thing for the ones I used. I Put a 1/4 inch bit into the back of the wheel just to...
I'm just playing around with the Idea but I'm considering trying to run a set of alloy rear wheels on the front wheels. I'm not trying to do a 4wd kit but could be open to the idea. Id like the car to be drive able after done.
im thinking if i cut...
Last post
well, back at square one. the seller was missing one of the axles in the set so I'm getting a refund :(
ill keep the b4 setup in mind until i find another set of axles that are cutoff at the end.
Hey guys. I'm looking for ideas on any tires that might fit the original RC10 1.6 rear wheels. I've heard people have used Tamiya Hornet tires or Sand Scorcher tires. Are there any other ones out there? Seems like all the re-release stuff has dried...
Last post
There are some JConcepts for the classic 1.7 rear wheels.
Maybe not the old school style but probably a better all round tire for traction.
Any real world experience would be appreciated. Thanks.
-Scott
Last post
The CW rims will work on a DS, just need a .200 spacer after the drive pins-
Thanks Reg, I just need to sand off 0.025 from each of the CW spacers and double them up. I am going to give that a try and update when I know something. Thanks for all...
...i qual 3rd with the car but i'd like to get the car more forgiving.
