Been feeling a little Blue - revisited lol

[nvxwax]

Ok so i got the sweet blue Old/New project from rick, I ordered some parts to complete it but have a problem, now i have built two of my own and did not have this problem, im not sure what is going on lol

I ordered

RPM RPM70272 Carriers
RC10 B44 Rear CVA Drive Kit ASC9756
Associated Alum Wheel Spacer B4/T4 ASC9608B
Custom Works Rear Wheel Spacer .125" CSW7208

This is the same setup i used on one of my black and green Old/New builds, One had the RPM carriers and one had the Losi carriers, Well i sold one, just so happens it was the one with the RPM carriers, SO now i dont have anything to compare it with, i would have thought i would have noticed this if the black and green car was like it.

Anyways....

With the CVA installed with two shims between the cva joint and the inside carrier bearing i dont get enough bite in the stealth drive cup, this is with the rear arms sitting just about flat (normal for my builds), then with the suspension compressed the lower side of the bone in just about out of the drive cup.

Any ideas?

[foots]

William I'll take a look when I get home this afternoon and get back with you.

[nvxwax]

William I'll take a look when I get home this afternoon and get back with you.

Thanks, it's probably something I did wrong lol, I just hope I did not do it twice lol

[scr8p]

you bought b44 cva's using arms designed for b4 cvd's. they're longer.

[nvxwax]

you bought b44 cva's using arms designed for b4 cvd's. they're longer.

Well crap lol, I thought they were the same as dynotech lol, i guess i have to get some new cva's lol,

[foots]

Yep thought about the arms on the way home. Sorry for not paying better attention earlier William

[Charlie don't surf]

you bought b44 cva's using arms designed for b4 cvd's. they're longer.

Well crap lol, I thought they were the same as dynotech lol, i guess i have to get some new cva's lol,

Just get the new b4 bones..

[nvxwax]

you bought b44 cva's using arms designed for b4 cvd's. they're longer.

Well crap lol, I thought they were the same as dynotech lol, i guess i have to get some new cva's lol,

Just get the new b4 bones..

I thought about that but looking at pictures the B4 has the cup on the bone, B44 has the cup on the axle lol

[Charlie don't surf]

Nah, the 4.1 bones...

[nvxwax]

Nah, the 4.1 bones...

Ok i see is it part ASC9672

[Seabass]

I see they got your problem answered. yes you will need the B4 bones for these arms, they were designed to work with B4 CVDs.

Can't wait to see it together.

Jake

[nvxwax]

Thanks,

I have the new bones on order , should be able to post some near complete pics up soon

[flipwils11]

I see they got your problem answered. yes you will need the B4 bones for these arms, they were designed to work with B4 CVDs.

Can't wait to see it together.

Jake

Glad I read this thread, I would have fallen into the same trap since I have a set of Jake's arms too.

[nvxwax]

I see they got your problem answered. yes you will need the B4 bones for these arms, they were designed to work with B4 CVDs.

Can't wait to see it together.

Jake

Glad I read this thread, I would have fallen into the same trap since I have a set of Jake's arms too.

lol, im glad my misfortune could help others , Its my fault for not reading the BST thread for the arms but at least its only a 10 dollar fix