B3 Diff build question
B3 Diff build question
Im putting together a factory team b3 kit that i got in a trade. I was putting the diff together and had a question before i proceed. Does #6575 the long screw go through that plastic washer with the ears or does that sit on the outside of the screw? Just dont want to have to pull it apart so i stopped until i get the correct anwser. Thanks in adavnce and love this forum.....everybody is so helpful!!
- scr8p
- Administrator
- Posts: 16540
- Joined: Tue Feb 07, 2006 9:46 pm
- Location: Northampton, PA
- Has thanked: 28 times
- Been thanked: 975 times
- GoMachV
- Super Member
- Posts: 11352
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 830 times
- Been thanked: 2459 times
Re: B3 Diff build question
It is shown correctly, it goes into the out drive after the screw as kind of a plug
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
Re: B3 Diff build question
Ok thats what i did but what stops it from falling out? Thats what made me think that screw would go through it to hold it into place.scr8p wrote:slide it down in the outdrive once the diff is built.
- flipwils11
- Approved Member
- Posts: 1904
- Joined: Sun Feb 14, 2010 10:30 pm
- Location: St Paul, MN
- Been thanked: 15 times
Re: B3 Diff build question
That washer on the far left is on the outside. It presses in behind the screw with the ears riding in the outdrive cutouts.
- scr8p
- Administrator
- Posts: 16540
- Joined: Tue Feb 07, 2006 9:46 pm
- Location: Northampton, PA
- Has thanked: 28 times
- Been thanked: 975 times
Re: B3 Diff build question
it sit in there fairly snug.vwlvr1980 wrote:Ok thats what i did but what stops it from falling out? Thats what made me think that screw would go through it to hold it into place.scr8p wrote:slide it down in the outdrive once the diff is built.
Re: B3 Diff build question
Ok cool thats what i did so now i can proceed......Thanks a ton guys!!flipwils11 wrote:That washer on the far left is on the outside. It presses in behind the screw with the ears riding in the outdrive cutouts.
-
- Approved Member
- Posts: 8921
- Joined: Tue Apr 08, 2008 2:44 pm
- Location: USA
- Been thanked: 8 times
Re: B3 Diff build question
The CVD in the drive cup keeps it from falling out-vwlvr1980 wrote:Ok thats what i did but what stops it from falling out? Thats what made me think that screw would go through it to hold it into place.scr8p wrote:slide it down in the outdrive once the diff is built.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 6 Replies
- 586 Views
-
Last post by e123
-
- 4 Replies
- 825 Views
-
Last post by NickTheGreek
-
- 2 Replies
- 465 Views
-
Last post by NRG
-
- 7 Replies
- 912 Views
-
Last post by littleVETTE
-
- 8 Replies
- 755 Views
-
Last post by a01butal
-
- 19 Replies
- 2113 Views
-
Last post by Konich
-
- 1 Replies
- 403 Views
-
Last post by Lonestar
-
- 12 Replies
- 2909 Views
-
Last post by CON2
Who is online
Users browsing this forum: Dutchy and 40 guests