Quadra-symmetric RC10

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

User avatar
Niki
Approved Member
Posts: 524
Joined: Wed Nov 02, 2011 11:32 am
Location: Finland
Has thanked: 3 times
Been thanked: 44 times

Quadra-symmetric RC10

Post by Niki »

1. INTRO

While designing longer arms for NIX10M, I started to think about so called quadra-symmetric suspension layout used from RC10B3 onwards.
Can it be done for tub chassis RC10 and how much tuning is needed?
Well, here it is... new long arms and new rear inner arm mounts. No other really special parts.
I wanted it to be as wide as possible within race rules.

-Niki-

rc10_quadra_01.jpg
rc10_quadra_02.jpg
rc10_quadra_03.jpg
rc10_quadra_04.jpg

User avatar
Niki
Approved Member
Posts: 524
Joined: Wed Nov 02, 2011 11:32 am
Location: Finland
Has thanked: 3 times
Been thanked: 44 times

Re: Quadra-symmetric RC10

Post by Niki »

2. PARTS

#6002 Worlds Car Kit
#7305 Nose plate (10T/GT)
#7207 Front bulkhead (10T/GT)
#7315 Nose brace tubes (10T/GT)
Front shock tower for 10T type nose
(In this build NIX80031 was used. Cut your own using SLS template or order CNC milled part from gomachv)
Front bumper if wanted/needed.
rc10_quadra_05.jpg
RC10 Quadra V2 Arm Set available now (update 2015-12-11)
Available at Shapeways also.
RC10_Quadra_arms_set_SLS.jpg
#1777 Shock alum ball/eyelet (Front shocks only)
asc1777.jpg
#9645 2-58x1/8 BHCS (Front arm inner hinge pin mounting)
asc9645.jpg
#6220 Inline axles
asc6220.jpg
#9672 B4 CVA Bone
asc9672.jpg
#9890 12mm clamping hex
asc9890.jpg
#9696 Rear hex wheels
asc9696.jpg
#73392 RPM Long Shank Rod Ends (AE #7230 Ball Cups might work also)
rpm73392.jpg

User avatar
Niki
Approved Member
Posts: 524
Joined: Wed Nov 02, 2011 11:32 am
Location: Finland
Has thanked: 3 times
Been thanked: 44 times

Re: Quadra-symmetric RC10

Post by Niki »

3. BUILD

Tap and drill out all SLS part holes.
rc10_quadra_10.jpg
91_worlds_conversion_026.jpg
RC10 bone and shims out. B4 bone and wheel hex in. No washers under shock lower end either.
rc10_quadra_11.jpg
Five washers inside rear shock. Four might work also. No washers inside front shocks.
rc10_quadra_12.jpg
There are good amount of front towers available for 10T bulkhead but I wanted to make my own.
SLS cutting template and Dremel Workstation were used. Later I swapped both rear (NIX63772) and front tower (NIX80031) with CNC machined parts made by GoMachV.
rc10_quadra_19.jpg
rc10_quadra_20.jpg
rc10_quadra_21.JPG
rc10_quadra_22.JPG
rc10_quadra_23.JPG

User avatar
abailey21
Approved Member
Posts: 273
Joined: Sun Feb 13, 2011 1:28 pm
Location: Leander TX
Been thanked: 2 times

Re: Quadra-symmetric RC10

Post by abailey21 »

This thread is worthless without sending me some!

Maybe sure to link them if you're going to sell cause a long arm runner would be choice!

fredswain
Approved Member
Posts: 1166
Joined: Fri Mar 11, 2011 9:20 pm
Location: Houston
Been thanked: 4 times

Re: Quadra-symmetric RC10

Post by fredswain »

I had been looking at doing the same thing too and also determined that the truck nose would have to be used. After thinking about things, all equal length arms would only be optimal if there was no front end kick. With front end kick, the front arms would optimally be longer. The exact length based on the level of kick. Losi got this right with the 22 (when using the 20° kick) which incidentally was also correct with the 91 Ifmar JR-XX car as well. All equal length is a big improvement over shorter front arms though so this will give you a much nicer handling car.
Raborn Racing Originals Shapeways store

User avatar
lmwong
Approved Member
Posts: 38
Joined: Mon Apr 13, 2015 9:24 pm
Been thanked: 2 times

Re: Quadra-symmetric RC10

Post by lmwong »

Subscribed! Build it and we will come with cash.

User avatar
ChisaiKuso
Approved Member
Posts: 526
Joined: Sun Jun 17, 2012 11:50 pm
Location: United States
Has thanked: 4 times
Been thanked: 27 times

Re: Quadra-symmetric RC10

Post by ChisaiKuso »

I will be watching this thread with great interest.
Something clever goes here...

User avatar
JK Racing
Approved Member
Posts: 4612
Joined: Thu Jul 19, 2007 6:32 pm
Location: Placentia, CA
Has thanked: 115 times
Been thanked: 217 times

Re: Quadra-symmetric RC10

Post by JK Racing »

Looks good Niki.
--Joey --
Vintage A&L and Factory Works
Old School Racer & Vintage RC Car nut
JKRacingRC.com

User avatar
Lonestar
Approved Member
Posts: 4270
Joined: Wed Dec 12, 2007 10:17 am
Location: Switzerland, yannow, in Europe (or almost)
Has thanked: 623 times
Been thanked: 167 times

Re: Quadra-symmetric RC10

Post by Lonestar »

basically a b4 with pan chassis

I love it :mrgreen:

Paul
AE RC10 - Made In The Eighties, Loved By The Ladies.
Blue Was Better - now, Blue Is Bankrupt.
Facebook affiliate program manager: "They go out and find the morons for me".
Life is short. Waste it wisely.

slow_jun
Approved Member
Posts: 958
Joined: Mon Oct 05, 2009 2:59 pm
Location: Manila/Singapore
Been thanked: 3 times

Re: Quadra-symmetric RC10

Post by slow_jun »

h#ll y#ah, im in...
“It is more shameful to distrust our friends than to be deceived by them.”
― Confucius

Headling
Approved Member
Posts: 545
Joined: Tue Dec 06, 2011 11:17 am
Location: Kent , UK
Has thanked: 25 times
Been thanked: 29 times

Re: Quadra-symmetric RC10

Post by Headling »

Want!

Looking forward to ordering up these parts!
If in doubt go flat out!

User avatar
Niki
Approved Member
Posts: 524
Joined: Wed Nov 02, 2011 11:32 am
Location: Finland
Has thanked: 3 times
Been thanked: 44 times

Re: Quadra-symmetric RC10

Post by Niki »

Thanks for your interest :D
2nd post updated, Quadra arms set heading to SLS machine.

-Niki-

User avatar
Niki
Approved Member
Posts: 524
Joined: Wed Nov 02, 2011 11:32 am
Location: Finland
Has thanked: 3 times
Been thanked: 44 times

Re: Quadra-symmetric RC10

Post by Niki »

Three quadra arm sets available in B/S/T-section.
In case someone wants to build Quadra-RC10 side by side with me :)
I'm starting my build any day now...

-Niki-

User avatar
Niki
Approved Member
Posts: 524
Joined: Wed Nov 02, 2011 11:32 am
Location: Finland
Has thanked: 3 times
Been thanked: 44 times

Re: Quadra-symmetric RC10

Post by Niki »

Build has started.
Post 2.PARTS and 3.BUILD updated.

User avatar
RichieRich
Approved Member
Posts: 2357
Joined: Thu Jun 15, 2006 3:42 am
Location: Los Angeles, CA
Has thanked: 39 times
Been thanked: 20 times

Re: Quadra-symmetric RC10

Post by RichieRich »

I was thinking of upgrading my Klein armed RC10 with these. Can I use the B4 rear axle carriers?
Image

  • Similar Topics
    Replies
    Views
    Last post

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No User AvatarCommonCrawl [Bot], No User AvatarGoogle [Bot], User avatarsilvertriple and 1 guest