Dadio's 3D Printing Stuff

The place to be for printing in 3D.

Moderators: scr8p, klavy69

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Dadio's 3D Printing Stuff

Post by Dadio »

This is my first attempt at 3D modelling and then 3D Printing a part , I've started with a fairly simple part , a front steering knuckle for a Yokomo Dogfighter YZ-834b , I thought i'd start with this as i need one and they are hard to find .
Comparison pictures of a real one and my printed part .
Real on the right .
Image
Image
Real on the left
Image
Image
There are a few bits that need revision , the hole for the track rod end is out of position, a couple of places could use a taper , the king pin hole is 0.5 mm to far from the edge and the taper towards the outer bearing is wrong , all that aside the only real reason it could not be used is the hole for the track rod end being too close to the edge making it weak .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

User avatar
coxbros1
Approved Member
Posts: 2063
Joined: Mon Dec 24, 2018 1:50 pm
Location: Energy, Illinois
Has thanked: 1719 times
Been thanked: 1500 times

Re: Dadio's 3D Printing Stuff

Post by coxbros1 »

Still cool!.....how long did it take to print?
Tap pic for clarity: Derek

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Re: Dadio's 3D Printing Stuff

Post by Dadio »

3 hours 20 min . just started printing a better version ....hopefully :lol:
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Re: Dadio's 3D Printing Stuff

Post by Dadio »

Two more not quite right versions :( , I can sort the errors out though as they were both over sites , there is some shrinkage occurring though so I'm going to have to oversize the bearing hole a bit , I'm thinking if this eventually comes out really well and I publish it for free on Thingiverse do I put dimensionally accurate sizes in or the dimensions that work and allow for shrinkage ? I'm guessing I should put the accurately copied measurements in so people can correct for the shrinkage of their printer and filament type ?
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

User avatar
GoMachV
Approved Member
Posts: 10963
Joined: Mon Apr 30, 2012 2:31 am
Location: Twin Falls, ID
Has thanked: 666 times
Been thanked: 1887 times

Re: Dadio's 3D Printing Stuff

Post by GoMachV »

I make all my drawings at actual size, different machines will print differently and different materials will shrink differently as well. Best to let the end user decide imo. They can adjust the percentage to adapt to their machine
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website

User avatar
ROH73
Approved Member
Posts: 623
Joined: Sun Feb 10, 2008 5:07 am
Location: State College, PA
Has thanked: 2 times
Been thanked: 18 times

Re: Dadio's 3D Printing Stuff

Post by ROH73 »

In my opinion, publish the model at as designed nominal size. You can list the critical dimensions for reference if you like. In my experience, FFM printers always make holes undersized, which is actually fine. I always open the holes up to the correct size with a drill or reamer. They're often out of round anyway, so some minor cleanup makes for a much better part.

tamiyadan
Approved Member
Posts: 2210
Joined: Wed Apr 07, 2010 8:45 pm
Been thanked: 8 times

Re: Dadio's 3D Printing Stuff

Post by tamiyadan »

.

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Re: Dadio's 3D Printing Stuff

Post by Dadio »

And here they are my first usable shareable 3D printed parts ! For reference i deliberately extended the hole for the king pin retaining set screw by 1 mm , might go to an extra 2 mm in future .
Image
Image
Image
Although you can't see it because it was on the bed the steering arm is fully radius'd around the edges in the file as per the real one .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

User avatar
ROH73
Approved Member
Posts: 623
Joined: Sun Feb 10, 2008 5:07 am
Location: State College, PA
Has thanked: 2 times
Been thanked: 18 times

Re: Dadio's 3D Printing Stuff

Post by ROH73 »

Looks great!!

User avatar
KidAgain
Super Member
Posts: 901
Joined: Fri Feb 01, 2019 7:11 pm
Location: So Cal
Has thanked: 257 times
Been thanked: 189 times

Re: Dadio's 3D Printing Stuff

Post by KidAgain »

Dang man great job.....................
Visit Nostalgic RC in the business section or @nostalgicrc on Facebook for your custom RC10DS parts

Gone: RC10, Jrx-2 and Jrx-t
Current: 3 SC10 first gens, 3 SC10 Street Outlaw's, 12 RC10 DS’s, Carbon RC10T, RC10LSS,RC10L, RC10 Graphite,RC10 B44

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Re: Dadio's 3D Printing Stuff

Post by Dadio »

Thanks guys :lol:
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

tamiyadan
Approved Member
Posts: 2210
Joined: Wed Apr 07, 2010 8:45 pm
Been thanked: 8 times

Re: Dadio's 3D Printing Stuff

Post by tamiyadan »

.

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Re: Dadio's 3D Printing Stuff

Post by Dadio »

I think I followed most of that Dan ,thanks .
The part is now on Thingiverse as " Yokomo Dogfighter YZ-834b Knuckle " so you can have a better look at the file .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

tamiyadan
Approved Member
Posts: 2210
Joined: Wed Apr 07, 2010 8:45 pm
Been thanked: 8 times

Re: Dadio's 3D Printing Stuff

Post by tamiyadan »

.

Dadio
Approved Member
Posts: 3682
Joined: Sun Apr 24, 2016 6:21 pm
Location: Guildford UK
Has thanked: 1931 times
Been thanked: 1808 times

Re: Dadio's 3D Printing Stuff

Post by Dadio »

I really do appreciate the help , I was trying to replicate the original part as a learning exercise and a shelf/semi usable part ,I only changed one bit the threaded hole for the king pin set screw I made 1 mm longer , I have A level design tech A level sculpture and National Diploma in Motor Vehicle Engineering as well as 25 years as a mechanic so I know a little of fatigue points a structural strength in designing stronger parts but that's not what I was trying to achieve here , I have a lath and mill that I can make structurally superior parts with .
The thing I really do need help with and where I appreciate your input greatly is the process specific to 3D printing methods like your tip on avoiding supports on overhangs .
I saw the whole build thread for that monster truck on RCGroups , very impressive !
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

  • Similar Topics
    Replies
    Views
    Last post
  • SilverTriple's printing stuff...
    by silvertriple » » in 3D Printing
    160 Replies
    4967 Views
    Last post by silvertriple
  • 3d printing some SRB stuff
    by j-sou » » in 3D Printing
    20 Replies
    4573 Views
    Last post by finman
  • Dadio's Airbrush Play
    by Dadio » » in R/C Off-Topic / Chit-Chat
    6 Replies
    535 Views
    Last post by Dadio
  • Dadio's latest dumb question
    by Dadio » » in Vintage Electronics
    11 Replies
    543 Views
    Last post by threesheds
  • Dadio's Humble Historic Collection
    by Dadio » » in The Gallery
    0 Replies
    1658 Views
    Last post by Dadio
  • 3D Printing
    by Smooth » » in 3D Printing
    3 Replies
    1148 Views
    Last post by Smooth
  • 3D printing.
    by OMC-Mikey » » in 3D Printing
    10 Replies
    1816 Views
    Last post by j-sou
  • 3D printing questions
    by TRX-1-3 » » in 3D Printing
    6 Replies
    115 Views
    Last post by silvertriple

Return to “3D Printing”

Who is online

Users browsing this forum: No User AvatarCommonCrawl [Bot] and 1 guest