CRP/Turbo Scorpion Racer

[mjtown]

Cool - thanks mate

Out of interest, which 12mm hex drives did you settle on? Axial or HPI?

[Hcp22]

HPI If remember correctly...

[mjtown]

Cool - I've used the Axial hubs but they're 4mm on one side and 5mm on the other, so they 'skew' a little when you tighten them up, which makes the wheels wobble a bit. Did you find HPI hubs with a constant 4mm bore?

I'm slowly working on the custom delrin centre gears by the way... between building the Optima Pro and other sidelines. I'll keep you up to date

[Hcp22]

Newly made Scorpion hop-ups!

Yesterday a small envelop arrived from US with something I have been looking for some time now to my runner! It contained two custom made wheel hubs so you can us a more modern 2.2” wheels with 12mm hex on your Scorpion runner. I

These adapters are done with a con that fit the Scorpion's odd con and they are 12mm long.

They fit real nice on the CRP CVD’s with no play what so ever and titans good when I mounted the wheel back on.

I did 8 minutes test run on ruff tarmac and grass, at one time I thought I would rip my old diff to pieces. But it holds up and so did the wheel hubs without loosen up. So I gone get me a few sets more of this “Whisler-hubs” tom my next runner built this fall/winter.

He is also making a real nice adjustable motor plate, front arms shaft blocks with set screws to keep the shaft in place and machined cassis rails. His eBay name is dwyz250

Dwaynes Motor Plate.jpg (43.39 KiB) Viewed 1691 times

Dwaynes Motor Plate.jpg (43.39 KiB) Viewed 1691 times

Dwaynes Rails and Clmaps.jpg (33.96 KiB) Viewed 1691 times

Dwaynes Rails and Clmaps.jpg (33.96 KiB) Viewed 1691 times

[mjtown]

Yeah, I grabbed the chassis and motor plate. Pretty nice work isn't it?

The alloy seems very strong!

[Hcp22]

I got the rails and the clamps and now the hubs. And I think they are grate for a runner and the price is affordable!

[Bo Wallen]

I got the rails and the clamps and now the hubs. And I think they are grate for a runner and the price is affordable!

Two envelope is shipped one should enter your space Monday the other Friday

[Hcp22]

I got the rails and the clamps and now the hubs. And I think they are grate for a runner and the price is affordable!

Two envelope is shipped one should enter your space Monday the other Friday

Nice

[Charlie don't surf]

I got the rails and the clamps and now the hubs. And I think they are grate for a runner and the price is affordable!

Are those billet rails? Has to be stronger than the stockers were

[Hcp22]

I got the rails and the clamps and now the hubs. And I think they are grate for a runner and the price is affordable!

Are those billet rails? Has to be stronger than the stockers were

Yes, 6061-T651 KAISER ALUMINUM

[Bo Wallen]

I got the rails and the clamps and now the hubs. And I think they are grate for a runner and the price is affordable!

Are those billet rails? Has to be stronger than the stockers were

Yes, 6061-T651 KAISER ALUMINUM

HolyMoly That's super strong

[nikos.r5]

Nice job!!! I would like to make a question.I am working on a scorpiom project (still collecting pieces) and I want to keep her old school. I intend to use the mechanic speed control and Iwould like to know if there is a limit for the motor . Can anyone give me some help which LeMans motors I can use..?

[Hcp22]

Hi and welkom to RC10talk
Any period LeMans will work
240S
360PT
480Gold
480S
480T

[Mr. ED]

I would suggest to keep your runs limited to 5 minutes though: to give parts the chance to cool down.
The 240 line would be pushing your luck to my feel.

[Hcp22]

That’s no problem; those old motors have so week magnets after 25 years. I run a modern LRP 2x17 in my Scorpion with LiPo without problems… But you have to check out your gearbox and adjust any play; otherwise it can end up in tears and a broken gearbox. This you should do anyway. But you are right about the running time; it should be max 5-6 minutes.