how to cut a body shell
-
- Approved Member
- Posts: 255
- Joined: Mon Jul 14, 2008 5:24 pm
- Location: Wellington, New Zealand
- Has thanked: 1 time
how to cut a body shell
Hi guys, I have been cutting out shells for 20 years now, but the thing I ALWAYS get wrong and stuff is when the body goes over the rear shock tower and clears the shocks
is there a trick to this ? or should I go back to my touring car bodys
ed
is there a trick to this ? or should I go back to my touring car bodys
ed
Hi, my name is Ed, and im a addict.
- slapshot1979
- Approved Member
- Posts: 928
- Joined: Wed May 26, 2010 6:18 pm
- Location: GTA Ontario,Canada
Re: how to cut a body shell
I use lexan scissors to rough out area and then a dremel to finish off.
Sleeps with a night light on, not because he's scared of the dark but because the dark is scared of him...........stay thirsty my friends
-
- Approved Member
- Posts: 1254
- Joined: Sun Mar 09, 2014 10:43 pm
- Location: peoples Republic of Australia
- Has thanked: 750 times
- Been thanked: 26 times
Re: how to cut a body shell
Hi Guys,
I am a complete amateur but on large curves in the wheels arches, after I cut them out I use a
small glass wrapped in wet and dry sandpaper to get nice curves.
On large straight areas after cut out I use the same sandpaper on the bench to get it nicely straight.
+ 1 on curved scissors but I bought a set of cheap nail scissors there were three in the packet 1
straight and 2 curved, they work well and were cheap!
Cheers, DaveM
I am a complete amateur but on large curves in the wheels arches, after I cut them out I use a
small glass wrapped in wet and dry sandpaper to get nice curves.
On large straight areas after cut out I use the same sandpaper on the bench to get it nicely straight.
+ 1 on curved scissors but I bought a set of cheap nail scissors there were three in the packet 1
straight and 2 curved, they work well and were cheap!
Cheers, DaveM
-
- Approved Member
- Posts: 255
- Joined: Mon Jul 14, 2008 5:24 pm
- Location: Wellington, New Zealand
- Has thanked: 1 time
Re: how to cut a body shell
slapshot1979 wrote:I use lexan scissors to rough out area and then a dremel to finish off.
what sort of bit do you use ?
ed
Hi, my name is Ed, and im a addict.
- shodog
- Approved Member
- Posts: 3816
- Joined: Thu Oct 05, 2006 3:09 pm
- Location: Washington
- Has thanked: 3 times
- Been thanked: 86 times
Re: how to cut a body shell
I gave up scissors long ago and use an exacto blade. Lightly score the plastic then bend and snap. I use a Dremel to clean up the curves
- slapshot1979
- Approved Member
- Posts: 928
- Joined: Wed May 26, 2010 6:18 pm
- Location: GTA Ontario,Canada
Re: how to cut a body shell
1/4 sanding drum
Sleeps with a night light on, not because he's scared of the dark but because the dark is scared of him...........stay thirsty my friends
- TRX-1-3
- Super Member
- Posts: 1760
- Joined: Sat Mar 29, 2014 12:13 pm
- Location: USAG Humphreys, South Korea
- Has thanked: 1418 times
- Been thanked: 777 times
Re: how to cut a body shell
Howdy,
I might use scissors to knock some chunks off, but I go danger close with an exacto knife. Super pointy tip, super slow, super carefull. I only go direct on the easy stuff, straight lines, sweeping curves, etc. When it gets tight and thick, I go to the dremel with a small sanding cone or drum. And then sandpaper for the super fine tuning. Keeping every inside cut radiused to help prevent tearing of the lexan. Give yourself plenty of light and think about the cuts.
"You can take more lexan off, but you can't put it back". And the best part is that it is fairly easy to screw up!
Some of the sweatiest concentration work is properly cutting a piece of vintage lexan.
Mark
And always test fit while trimming. If the back portion by the shock tower always jambs you up: try fitting/trimming from the front to the back. Sometimes I'll lay the clear partially trimmed body on/over the chassis and eyeball some cut limits and mark those on the body with a small pen dot, ect.
Take your time.
I might use scissors to knock some chunks off, but I go danger close with an exacto knife. Super pointy tip, super slow, super carefull. I only go direct on the easy stuff, straight lines, sweeping curves, etc. When it gets tight and thick, I go to the dremel with a small sanding cone or drum. And then sandpaper for the super fine tuning. Keeping every inside cut radiused to help prevent tearing of the lexan. Give yourself plenty of light and think about the cuts.
"You can take more lexan off, but you can't put it back". And the best part is that it is fairly easy to screw up!
Some of the sweatiest concentration work is properly cutting a piece of vintage lexan.
Mark
And always test fit while trimming. If the back portion by the shock tower always jambs you up: try fitting/trimming from the front to the back. Sometimes I'll lay the clear partially trimmed body on/over the chassis and eyeball some cut limits and mark those on the body with a small pen dot, ect.
Take your time.
Hope you're doin' something fun.
- jwscab
- Super Member
- Posts: 6506
- Joined: Wed Jan 28, 2009 9:42 am
- Location: Chalfont, PA
- Has thanked: 10 times
- Been thanked: 453 times
Re: how to cut a body shell
yep, third(?) the xacto method. You can use the blade and a straight edge, score, and break. even when you get to the thick tight curvy sections, a score, and rescore, and a pair of needle nose pliers to flex back and forth to snap off in small sections. also, if you are dealing with a really complex outline, don't feel bad about slicing the excess parts into sections, so that the break lengths are shorter. for instance, working up to the shock tower area, make your scores along the bottom edges of the body front and rear, and then bring them up into the shock clearance area, then cut right across about midway, and pull all that off. then you only have that small finger of lexan you need to carefully remove. think of it like an orange peel, you don't have to take it all off in one shot.
then follow up into really tight spots with a sanding drum or rotary file/burr. just keep the rpm low so you grind the plastic, not melt it. It's actually a good idea to follow any of those tight areas with the sanding drum, since lexan is notch sensitive, it will crack if the edge isn't smooth. that's usually why you end up with cracks around the shock tower area in the nose on most old bodies.
then follow up into really tight spots with a sanding drum or rotary file/burr. just keep the rpm low so you grind the plastic, not melt it. It's actually a good idea to follow any of those tight areas with the sanding drum, since lexan is notch sensitive, it will crack if the edge isn't smooth. that's usually why you end up with cracks around the shock tower area in the nose on most old bodies.
- integra22t
- Approved Member
- Posts: 637
- Joined: Fri Aug 09, 2013 1:36 pm
- Location: Kingston On.Ca
- Been thanked: 2 times
Re: how to cut a body shell
if the body is already painted and your trying to cut out ie: buggy body .. flip the car upside down place the body on the bottom side of car ( body right side up ) and use a square to help find the cut lines around shock towers and make your first cuts on the inside of your lines as you can always trim more but never replace
- marlo
- Approved Member
- Posts: 2071
- Joined: Tue Jan 22, 2013 5:31 pm
- Has thanked: 21 times
- Been thanked: 21 times
Re: how to cut a body shell
I rarely cut these days, but when I do, ^^ same thing, always perfect. I go over all edges with some fine grit paper after, being careful no to scratch the body.slapshot1979 wrote:I use lexan scissors to rough out area and then a dremel to finish off.
-
- Approved Member
- Posts: 255
- Joined: Mon Jul 14, 2008 5:24 pm
- Location: Wellington, New Zealand
- Has thanked: 1 time
Re: how to cut a body shell
20 years.....
20 years and I have never seen/heard about a exacto knife way...
just tried it on some scrap and wow its so easy now!
still don't quite follow the dermal though.
so you use a sanding bit or some sort of cutter ?
ed
20 years and I have never seen/heard about a exacto knife way...
just tried it on some scrap and wow its so easy now!
still don't quite follow the dermal though.
so you use a sanding bit or some sort of cutter ?
ed
Hi, my name is Ed, and im a addict.
-
- Approved Member
- Posts: 255
- Joined: Mon Jul 14, 2008 5:24 pm
- Location: Wellington, New Zealand
- Has thanked: 1 time
Re: how to cut a body shell
thank you!
I have a couple of touring car bodys to cut out over the next few days, as well as my mirage body, and want to make a good job of it.
ed
I have a couple of touring car bodys to cut out over the next few days, as well as my mirage body, and want to make a good job of it.
ed
Hi, my name is Ed, and im a addict.
- DMAT
- Approved Member
- Posts: 884
- Joined: Wed Mar 20, 2013 8:53 am
- Location: Baton Rouge, La
- Been thanked: 3 times
Re: how to cut a body shell
and here I was just using scissors. Id like like 50 little cuts across each wheel arch and use a larger pair of scissors for the straight line cuts.
I do use a dremel at the top of the shocks to create a nice even curve.
I do use a dremel at the top of the shocks to create a nice even curve.
- Coelacanth
- Approved Member
- Posts: 7375
- Joined: Thu Jul 29, 2010 6:20 pm
- Location: Alberta, Canada
- Has thanked: 16 times
- Been thanked: 292 times
Re: how to cut a body shell
I cut out most of the body, leaving about a centimeter or so outside the cut lines. I also score about 80 - 90 percent of the lines with a fresh X-Acto blade, but sometimes use the little curved Lexan scissors for the corners of the body, especially if they're quite tightly squared-off. The short curved scissors help make those tough angle cuts, often the Lexan is thicker there. I also make the angle cuts just outside the desired cut-line, so that I can use a Dremel sanding drum or file to remove the Lexan up to the cut-line.
Completed projects: CYANide Onroad Optima | Zebra Gold Optima | Barney Optima | OptiMutt RWD Mid
Gallery - Coel's Stalls: Marui Galaxy & Shogun Resto-Mods | FrankenBuff AYK Buffalo | 1987 Buick GNX RC12L3
Gallery - Coel's Stalls: Marui Galaxy & Shogun Resto-Mods | FrankenBuff AYK Buffalo | 1987 Buick GNX RC12L3
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 1 Replies
- 725 Views
-
Last post by yellowdatsun
-
- 36 Replies
- 7150 Views
-
Last post by SluggoV2
-
- 5 Replies
- 1939 Views
-
Last post by Basher67
-
- 4 Replies
- 1334 Views
-
Last post by Coelacanth
-
- 10 Replies
- 1754 Views
-
Last post by RichieRich
-
- 2 Replies
- 668 Views
-
Last post by Charlie don't surf
-
- 2 Replies
- 567 Views
-
Last post by bigtenuk
-
- 8 Replies
- 868 Views
-
Last post by teman
Who is online
Users browsing this forum: No registered users and 3 guests