RC10Talk - The Net's Largest Vintage R/C Community

I came across an ok deal on this roller and thought it could make a good runner.
.
Screenshot_20211222-172742.png
.
After cleaning, dying, outdrive bearing mod, and reassembly it seems to be turning out pretty well.
.
PXL_20211223_022658508.jpg...

Available again for the Worlds and short arm cars. This time in black.

Hello friends of the RC10

I'm alway in doubt wether I shoud use my RC10s in bad conditions (dirt, mud, snow, skatepark...). It would be a lot of fun, but it would also be a shame to destroy original parts. So I bought a CNC Machine and I will build...

I started an ambitious project to list every single vehicle release by Team Associated from its beginning. You can see the current status here: It should work fine in mobile and desktop screens.

I've been able to verify all the vehicle years with...

Are all pushrod wires the same size? I'd like to replace the tie rod link I have with a more vintage solution. Are the wires for zbend pushrods the same diameter?

would something like this be work if I cut them down

Would I shop that...

Need to find the plastic bits that go inside the team car shocks. Does anyone know where to get them ?

All, Amain, RC Planet and others have a $60 off flash sale on the Losi Mini-B Pro Kit. Final price $79 shipped - Hard to beat.

-limestang

Back in my much younger days I picked up a gold chassis rc10 that the previous owner had converted to a truck. The truggy has the steering system in the non stock location allowing the steering linkage to be perpendicular to the steering arm.

This...

Hi there, I’m just purchased a Team associated/mip 3/16 cvd kit. What else is needed to install on rc10 team car?

I have the following RC10 graphite chassis with a gold motor guard (I found some rear and front white nylon a-arms not shown in the picture). I forgot how it became part of my collection years ago. It would take a lot of work and money to get it...

Hello Friends of the RC10

First pics of a little project: RC10 how it could have been back then. Front nose plate and bulkhead from the RC10T with longer arms. Geometry similar to RPM, milled by hand from white polyamide.
Back end will be with hex...

While searching ebay, I came across this pile of Team Car parts. Since I had most of the parts needed, I decided to go ahead and rebuild it. And since I don't actually have a Team Car, it made the decision easier.

The shock towers and nylon parts...

As per title im just getting back into racing after 25 years away. Ive got a B6.1 but my local club also runs vintage races so Im thinking of campaigning one of my old RC10 team cars. First question is parts availability seems pretty sparse for...

Is this a rare weave pattern? I have several graphite chassis and this is the only one like this I've ever seen, anyone else have this weave pattern?

Hi all. I am looking for a bit of advice.

I am in Germany trying to find a turnbuckle set (including balls and cups) for my Cadillac RC10, but having a real tough time finding the 4-40 set here (or it is super expensive if so).

I can get a lot of...

That was a few years ago, just having a little fun with my (by this time) new milling machine.

Howdy,

I bought another car from the original owner. He was only about 25 miles from me.

It’s got quite a few scratches on the original chassis and the one it’s currently fitted with. From what I was able to look up, it looks like maybe a Trinity...

I have wanted one of these since my best friend from childhood had one in the late 80's. I picked this up on eBay last night, hope I didnt get hurt too bad at $300. It was advertised as an A stamp Andy's edition . What can you all tell me about this...

I already have another thread detailing one of these rare beasts which I picked up a while ago from Richard Isherwood (who was sponsored by Don Ison of NODIS prior to his Team Kyosho days), but never did I think i would locate another, let alone...

Thankfully one of the items that didn't get purged in early 2000s was my original RC10 Graphite chassis, with original box , manuals with stealth transmission. Although the parts were all used on other cars at time, my battle worn chassis (as I...

Hey guys! I asked on the FB group but I didn't really get an answer. I'm in need of the standard 3/16 x .01 shims that are used for axle spacing. I see Amain has a 20 pack for $6 which isn't crazy, I guess. I thought McMaster might have a 50 or 100...

Another unicorn has landed in my lap... this one being a genuine loft find which was discovered whilst I was actually researching the Brimod prototype car. This 4WD car was developed by MMS over in the UK (around 12months before they developed the...

Anyone know where I can get something like this for my RC10 classic?

Rebuilding my Cadillac RC10 and figure why not upgrade a few bits while I am at it :-D

Are there longer rear arms that might be necessary to get something like this to work?

Six-gear transmission. Every spur I have is like this...a few og nylon and a bag full of Kimbroughs.

With all the love for blue builds going on around here lately, I figured I better start this one soon. I've been collecting parts for a little bit and while it's nowhere near as hard a process to locate these like some of the gold pan vintage stuff...

In 2018 I found a brand new hydradrive for a good price but without any specific goal.
After a conversation on the subject with another vintage addict at my local track,
I heard of an english shop (DMS Racing) selling reproduction of a shaft...

For looks?

img19357_25082010134944_1.jpg Original_RC10,_minus_wing,_released_by_Team_Associated_in_the_early_1980s,_part_number_6000.jpg vintage_rc10_racer_8.jpg

Just curious, after a long focus on Losi I am a recent convert to the RC10 side and as usual going off the deep end. 2 new rere World's, a rere Classic and a few real old ebay clunkers for restoration have already entered my life. I intend to run...

Not sure if this post belongs here, but I wasn't sure where else to post it. I just got home from another visit to the local hobby store. I found a B4 Top Shaft! That was what I was after all along so I could avoid eBay pricing. Pretty excited to...

Hi folks,

has anyomne come across a modern, more-or-less equivalent replacement for the original stealth slipper spring, aka p/n 6587?

On another note - was there anything so special about the thrust washer assembly p/n 6594 - looks like plain...

Hey guys! I moved into a new house earlier this year. Yay! RC stuff is almost done being unboxed. Lots of organizing going on now. Anyway, some of my cars and most of my projects have been boxed up for 2-3 years and are now seeing the light. One of...

Hello, can anyone let me know what these may be from?

Many thanks. A59ED742-74F3-4DF0-8473-0B5C168EE0F5.jpeg

Are there any of the newer looking low fitting bodies that will work well on the gold pan chassis?

Hi all,

So, I have been asking questions on things for my RC 10 (cadillac). I am replacing a few missing electronics and will be doing a re-build to make sure the shocks are in shape with oil, re-grease the gearbox, and do a general clean up...

Hi all,

I was wondering if anyone had any leads where one could get a bearing set for an RC10 classic kit in the EU (Germany). I have a Cadillac RC10 that is missing some front bearings bought thought it might be fine to just replace them all at...

I was just wondering if anyone is still making these chassis kits, either the NIX91 or the Justin/Fred version? Maybe someone has a spare that they'd like to sell or trade?

Thanks in advance

Starting a new build of one of the cars I always wanted, the Stealth Car of the early 90's. This one is a bit different from the NX91 car or other reproductions I have seen on this site, it is based on the 6 gear version of the RC10 that won the...

There's a RC10 paint job that I'd like to replicate that I first saw in the RCCA shootout between the RC10 and the Ultima. I've seen it elsewhere floating around and wondered if it was the same car. Here's some pics:

I first saw it like this in an...

Just looking at gearing for the six gear with a silvercan.

I noticed on this chart, the FDR for the 27T stock brushed seemed a bit high. I assume this is for an open endbell stock motor. My thoughts were something like 5.5:1 - 6.0:1 using the small...

C3C85F85-7A8E-4D24-837A-E0E5E82019B7.jpeg 135213B8-6BDD-4A3E-874F-39E26AA986CF.jpeg B9876CC0-0C66-43AC-8358-32DB1B93BED7.jpeg 4BD13FFF-86A6-40B3-8CA1-2F8BBC23533C.jpeg C698B58F-F220-494F-A1D2-FE4AA289035F.jpeg...

My vintage rc habits have been put on hold all summer as I got more involved with the drag racing side of the hobby. I decided to combine the two, and this is the result.

Hey Guys,

Just wanted to say hi and ask a quick question. After scouring the internet, I found a car that was virtually (Spec wise) identical to the car I had in high school. It may not be the most desirable (Cadillac A Stamp) but it was the one...

Are nylon parts on the early RC10's durable enough to use for a runner?

Are the later black nylon parts the same composition as the white parts?

I have a 1992 TRX-1. A lot of the original nylon parts had to be replaced as they were very brittle....

Hi guys, I have a question to ask you, I found a new, assembled Team Associated RC10 World's Car for sale; how much do you think I should pay it, what is its value considering the conditions that are new? Thank you, see you soon!!!!