I'm trying to get a certain color for a 1/10 '67 Corvette body. I can't find the exact color match in Tamiya, or Duratrax polycarb spray paints.
I've seen some people say that if the inside of a lexan body is roughed up with a green pad to produce a scratchy looking adhesion surface, and then de-greased with soap and water, that then nearly any spray paint will stick to that surface. Has anyone tried this, or have experience with this?
Wanting to try color matched Chevy Marina Blue spray paint for autos, inside lexan.
Sanding helps with adhesion, but I found if you get very aggressive it'll leave scratches on the Lexan that'll be visible after you paint.
Could spray couple coats of Tamiya PS-55, followed by your automotive color coats, then back coated with the PS color of your choice. The auto paint mixes with the Tamiya clear and becomes flexible while the PS back coat acts as an encapsulator.
Or you could ask your local PPG or Dupont paint store to mix you up a color matched spray can with a flex agent for use on plastic. Effectively making it like Tamiya paint.
I have PS-55, but I used it to dull the outer shine of the ragtop on this VW Bus model, to make the shiny top contrast to the dull vinyl look of the sunroof/ragtop:
I may have to try the 976 paint-matched aerosol, just to know for certain if it can be done on lexan.
morrisey0 wrote: ↑Mon Feb 12, 2024 8:19 am
I would think PS49 could get you there with the correct backing.
tamiya-ps-paint-chips-2e4c.jpg
I was checking that PS-49 out, but it has a matte anodized finish, while it could pass if I weren't being too particular, it doesn't have the right blue overall, Sky PS-49 looks like silver over blue, I need blue over silver.
Marina Blue Metallic is hard to capture in pictures, it's definitely sparkly, but not like an old 70's boat, it has a silver sheen below the blue that moves as you walk around and catch the sun off of it.
There's nothing foolish about using automotive paint on lexan. Just "prime" the body with PS-55 and I think you'll be fine.
Also, apparently adhesion promoter can be used with lexan but I've never tried it.
XLR8 wrote: ↑Tue Feb 13, 2024 9:30 am
There's nothing foolish about using automotive paint on lexan. Just "prime" the body with PS-55 and I think you'll be fine.
Also, apparently adhesion promoter can be used with lexan but I've never tried it.
Tamiya PS-55 is Flat clear, the Flat won't dull the layer beneath it?
I've only used PS-55 on the outside of lexan so far. Will test some plastic bottles with PS-55 on the inside this time.
I'm not sure how well automotive paint will bond to Lexan. For one thing, it's meant to bond to properly-roughed-up primer on a hard surface, and you can't be priming the inside of a Lexan body shell or that's all you'll see, glossy battleship grey. It's also not meant to be flexible so auto paint on Lexan might crack or chip if the Lexan is stressed. There's no harm in trying, of course.
Coelacanth wrote: ↑Tue Feb 13, 2024 3:26 pm
I'm not sure how well automotive paint will bond to Lexan. For one thing, it's meant to bond to properly-roughed-up primer on a hard surface, and you can't be priming the inside of a Lexan body shell or that's all you'll see, glossy battleship grey. It's also not meant to be flexible so auto paint on Lexan might crack or chip if the Lexan is stressed. There's no harm in trying, of course.
I had heard that lightly scuffing/scratching the inside of the lexan body with a kitchen green pad, not gouging, or deep scratches, just even surface roughness on the entire inside, then degrease, and then paint with nearly any spray paint - that this can work for lexan. Might as well give it a try. I wouldn't expect the paint to survive bashing, or to be flexible like polycarb, this one will be a shelf body, or a scale speed cruiser. I'll test this all on plastic bottles first, for color, then adhesion.
I use poly acrylic spray paint. Its cheap and found all over.
I also back with the cheapest white I have laying around. Poly paint first and the white doesn't crack. Don't have to buy expensive white. Just spray white before the poly colors cure.
If you use an acrylic clear first you can put any paint over it while it's still tacky.
XLR8 wrote: ↑Tue Feb 13, 2024 9:30 am
There's nothing foolish about using automotive paint on lexan. Just "prime" the body with PS-55 and I think you'll be fine.
Also, apparently adhesion promoter can be used with lexan but I've never tried it.
Tamiya PS-55 is Flat clear, the Flat won't dull the layer beneath it?
I've only used PS-55 on the outside of lexan so far. Will test some plastic bottles with PS-55 on the inside this time.
The flat clear won't affect the finish in any way. Assuming, of course, that you are painting the inside of your body shell, the lexan provides a glass-like reflective finish.
Coelacanth wrote: ↑Tue Feb 13, 2024 3:26 pm
I'm not sure how well automotive paint will bond to Lexan.
Bonds fine... some brands just doesn't hold up to abuse as well. When we were in school all our Lexan bodies were shot with automotive paint because it was cheaper and more readily available.
What makes Tamiya PS a "lexan paint" is the use of acetone in their carrier instead of say, isopropyl. Acetone etches the plastic and creates more adhesion. Any spray paint with acetone will produce the same results as Tamiya PS.
If color match is the most important factor, auto paint is the easiest solution, with PS-55 acting as a primer if you want a more resilient paint job. I gurgled and found a video... 3:30 in he demonstrates the flexibility of Tamia TS with PS-55 as a base:
In the end there is no wrong type of paint, just multiple options each with their own advantages and disadvantages.
Coelacanth wrote: ↑Tue Feb 13, 2024 3:26 pm
I'm not sure how well automotive paint will bond to Lexan.
Bonds fine... some brands just doesn't hold up to abuse as well. When we were in school all our Lexan bodies were shot with automotive paint because it was cheaper and more readily available.
What makes Tamiya PS a "lexan paint" is the use of acetone in their carrier instead of say, isopropyl. Acetone etches the plastic and creates more adhesion. Any spray paint with acetone will produce the same results as Tamiya PS.
If color match is the most important factor, auto paint is the easiest solution, with PS-55 acting as a primer if you want a more resilient paint job. I gurgled and found a video... 3:30 in he demonstrates the flexibility of Tamia TS with PS-55 as a base:
In the end there is no wrong type of paint, just multiple options each with their own advantages and disadvantages.
Really appreciate that example, thanks for that!
Interesting to see the PS-55 was able to support Tamiya TS, and be that flexible still; that also adds a ton of color and spray-type options. Also makes this video testing metallic blues even more relevant, as these are TS and lacquer.
I have a nearly full can of PS-55 Flat Clear already, I'll get a can of 976 Marina Blue Metallic auto-matched aerosol spray, and we'll see what can be done. Might be a couple of weeks before I can get this going.
Coelacanth wrote: ↑Tue Feb 13, 2024 3:26 pm
I'm not sure how well automotive paint will bond to Lexan.
If color match is the most important factor, auto paint is the easiest solution, with PS-55 acting as a primer if you want a more resilient paint job. I gurgled and found a video... 3:30 in he demonstrates the flexibility of Tamia TS with PS-55 as a base:
That's cool, I didn't know there was this PS-55 clear primer that will let automotive paints properly bond to Lexan. In my old-school mind, whenever I think of primer, I think of solid grey or red paint primer.
To sum up the post below. I used a duratrax rattle can to paint with and it was horrible. Tamiya color cans are gone at my LHS. What can I use in place since i dont want to make the jump to an airbrush system yet.
So with tamiya color paint no...
Last post
Just bought some Spaz Stix paints. FL Yellow, FL Blue, and White. We'll see. I have only used the Tamiya and Pactra paints in the past. With the RTR and pre- painted bodies, who in the hell needs a quality paint anymore? Right? Wuuf. I'll report...
I'm really having a difficult time finding where to purchase spray cans of Tamiya paint. My LHS says they can only get polycarbonate paint, and they only order it once a month or less... so basically they don't want my money, or maybe it's not worth...
Last post
Thanks guys... I'll check out those options. I'm in Kitchener actually so Hobby and Toy Central might be a good option!
Hi all
Where I live its hard to get a hold of the tamiya spray paint cans (or any lexan sprays).
I managed to get a hold of 2 cans... (white and blue)
I need to be very careful with the amount I use as these 2 cans need to be enough for 2 cars (1/10...
Last post
Per Tamiya, the 100ml can is sized specifically to coat one complete model. I tend to use more when doing pan car bodies, but less when doing buggies.
Hi All,
I'm looking to spray paint a Vanning shock and match as close to the original red annodized color as possible. Just curious if anyone has experience with a paint brand / color that is a very close match?
Thanks
Last post
Thanks guys,
this is for the shelf. I'll try the Tamiya clear red.
Cheers
Vintage associated Nissan body that a friend of mine that I race slot cars with painted for me.
I thought it looked pretty good and he even made me some nice Nissan Decalls
I gave him some other old bodies and I can't wait to see what they turn out...
Last post
Ok, Ill see what I can do, I made a special trip with a work vehicle 31/2 hours to be exact to scope out that shop....Ill try next week. The bodys have a Extremely old Associated logo on them. And were almost impossible to read, but I did see...
So, Tamiya used to offer a nice gray lexan paint, yet there's a mystery about it. The top cap, where the part number would be, was just PS . There was no number after the PS like on ALL of their other paints. Depending on where you look, you may or...
Last post
So the body that first had clear sparkle put on, and then the gray Humbrol, is holding up fine. It seems the Humbrol holds well to other paints, it just needs something else to hold better to the lexan. So for anyone wanting to use gray (my favorite...
I keep reading on ebay sellers descriptions where they are writing.....
this shell (lexan) could easily be stripped and re-painted to look like new
What do they know that I don't? Is there a new amazing product out there?
I...
Last post
Hi guys,
Thanks a lot for your kind advice on products and paint stripping. I am sorry I hadn't replied before I have been exceptionally busy. I will let you know how it goes.
I am on holiday now though, so it will be a while before I get back to...