DS build question
DS build question
I have a DS Racer's kit I'm building from NIB. After building the tranny I have these 2 plastic washers left but I don't know where they're used and can't find them in the manual. I also ended up with an extra locknut. The washers measure 1/8" ID x 1/4" OD x 1/16" thick. Any help?
- GoMachV
- Super Member
- Posts: 11352
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 830 times
- Been thanked: 2459 times
Re: DS build question
The nut looks gold which means it's a slipper nut (5-40 thread)
The plastic washers look like what is used with dogbones in the outdrives. With universals they are not used.
The plastic washers look like what is used with dogbones in the outdrives. With universals they are not used.
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
Re: DS build question
I was putting the parts bags away after I completed each section and these spacers and nut were leftover from the bags involved with building the tranny.
I had all the shock spacers needed when I got to those bags. Plus they are 1/32" thick in this kit.
I went back and checked the manual and it doesn't show the spacers when using dogbones either.
I thought maybe they were spacers for between the bulkhead and tranny brace. However the manual doesn't show to use them there and it doesn't look they they're needed anyway. The brace is level.
I had all the shock spacers needed when I got to those bags. Plus they are 1/32" thick in this kit.
I went back and checked the manual and it doesn't show the spacers when using dogbones either.
I thought maybe they were spacers for between the bulkhead and tranny brace. However the manual doesn't show to use them there and it doesn't look they they're needed anyway. The brace is level.
- LoboNYC
- Approved Member
- Posts: 778
- Joined: Tue Apr 09, 2013 12:26 pm
- Location: Staten Island, NYC
- Has thanked: 814 times
- Been thanked: 344 times
Re: DS build question
You got to love this forum for all the knowledge available and provided by members.
I've never had the pleasure of building a NIB DS or NDS for that matter, so this is good to know when I decided to open the one I have. its a racer kit so I would have been in the same situation.
Thanks gomachv!
By the way...I wasn't aware that the qualifier kit lacks a slipper clutch until I got a few of them. Thanks Romulus22 for providing a slipper for a NDS project still in the works.
tommy2c, did your kit come with body? if not what body are you thinking of using? damn DS addiction is killing me
I've never had the pleasure of building a NIB DS or NDS for that matter, so this is good to know when I decided to open the one I have. its a racer kit so I would have been in the same situation.
Thanks gomachv!
By the way...I wasn't aware that the qualifier kit lacks a slipper clutch until I got a few of them. Thanks Romulus22 for providing a slipper for a NDS project still in the works.
tommy2c, did your kit come with body? if not what body are you thinking of using? damn DS addiction is killing me
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 7 Replies
- 831 Views
-
Last post by Charlie don't surf
-
- 9 Replies
- 1768 Views
-
Last post by klavy69
-
- 10 Replies
- 1308 Views
-
Last post by Lonestar
-
- 47 Replies
- 3420 Views
-
Last post by SRTracer121
-
- 11 Replies
- 964 Views
-
Last post by treehugger
-
- 16 Replies
- 2258 Views
-
Last post by stingerrray
-
- 100 Replies
- 15605 Views
-
Last post by DerbyDan
-
- 20 Replies
- 4021 Views
-
Last post by DFaultXEX
Who is online
Users browsing this forum: No registered users and 2 guests