Gomachv's 4wd RC10 project- finished!

Post by **GoMachV** » Fri Feb 14, 2014 4:39 pm

Should I add teeth?

Post by **THUNDERSTRIKE1** » Fri Feb 14, 2014 6:31 pm

Just add two bugsbunny teeth at top the hole!!

don

Post by **Phin** » Fri Feb 14, 2014 6:36 pm

gomachv wrote:Should I add teeth?

Don't you mean a grill?

Post by **GoMachV** » Fri Feb 14, 2014 6:39 pm

I don't think I could fit his head under the pin router to try it!

Post by **myfordcnc** » Fri Feb 14, 2014 9:32 pm

please try.

Post by **vintage AE** » Fri Feb 14, 2014 10:18 pm

a red tongue would be easy

Post by **GoMachV** » Fri Feb 14, 2014 10:20 pm

vintage AE wrote:a red tongue would be easy

If I did, we could finally name this pig!

Miley!

Lol

Post by **vintage AE** » Fri Feb 14, 2014 11:15 pm

only if we could see her twerk

Good call though!

Post by **THEYTOOKMYTHUMB** » Fri Feb 14, 2014 11:37 pm

Perhaps??

BTW, if you search for images of sex dolls prepare to be creeped out...

Post by **GoMachV** » Fri Feb 14, 2014 11:57 pm

Post by **THEYTOOKMYTHUMB** » Sat Feb 15, 2014 12:21 am

For whatever reason that doll was named "Virginia Thomas" by the manufacturer. You could name the car "Virginia" and paint the body WWII fighter plane style.

Post by **GoMachV** » Mon Feb 17, 2014 7:49 pm

It runs

Ne belt tensioner, I have only heard it skip a couple times but I'm only running a midnight stock motor and 6 cell pack, all old school. Feels ok, needs a lot of suspension work (not my strong point) but as a proof of concept.....it works!

Note: I swapped out the rear hubs and tires as the 2.2 were so tall it was under driving the front end. This is fairly square now.

This will most likely end up on eBay very soon. I have ideas to implement on a newer and more purple chassis

[youtube]Aypz4LFsswM[/youtube]

Post by **myfordcnc** » Mon Feb 17, 2014 8:21 pm

Sweet!! What are your plans/thoughts for the tensioner?

Post by **GoMachV** » Mon Feb 17, 2014 8:24 pm

The belt needs to tension the top, and that creates a problem unless it's minimal. I'm going to play with it a bit first- but this is one thing I hope to overcome with a couple little tweaks on the next one

Post by **teman** » Mon Feb 17, 2014 8:28 pm

gomachv wrote: It's still a ways off....but don't worry I'm sure I will be able to sell a few before long

If you can make this happen, I'm down and others for sure

RC10Talk - The Net's Largest Vintage R/C Community

Gomachv's 4wd RC10 project- finished!

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Re: Gomachv's 4wd RC10 project- IT RUNS (but still unnamed)

Re: Gomachv's 4wd RC10 project- IT RUNS (but still unnamed)

Re: Gomachv's 4wd RC10 project- IT RUNS (but still unnamed)

Re: Gomachv's 4wd RC10 project, still unnamed and unproven

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online